I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hello.
I am developing using nRF5340DK and nRF Connect SDK v2.8.0. I want to create a DFU distributor that updates both Application core firmware and Network core firmware...
We have been porting from v2.5.3 to v2.8.0. So far the only thing that we've had to change has been the board files, but one thing that was noticed is that the CONFIG_FLASH_LOAD_OFFSET...
Hello,
On my Thingy:53, I would like to try Matter. I use Google Home to connect to Matter and I use the QR codes on the following page: docs.nordicsemi.com/.../README.html...
I need to build a PC-based workstation (Windows 10) for programming our boards that contain a nRF52840. Do I need to download / install the command line tools and the nRF...
I'm trying to update the modem core from the standard firmware to the production test image on my nRF9161 dk to experiment with the PTI before doing the same on a custom board...
I'm using firmware 1.3.6 and SDK 2.7.
I have a ppp connection problem for IPV6. Tables below show connection status:
When I use SLM:
ISP / PDP + APN
"IPV6" ...
I read some previous posts that there was limited support for sysbuild for the VSCode extension. There are two things that I noticed: 1. When creating a build configuration...
For a project i need to use the channel sounding feature of bluetooth. On checking samples on nRF Connect SDK couldn't find any examples. But the Zephyr project is providing...
I run a matter light_switch demo on my nrf54l15dk board, and I added these two configurations in prj.conf to enable dfu over bt smp. Built and burned the firmware into my...
Hi,
I am currently working on creating a Custom Profile, and have used Peripheral Sample code. I tweaked the code and was able to send 512 bytes of data on 8 different characteristics...
Hi,
I'm working on a GPS tracking application using nRF9160. The application is to send sensor data and location data every 15mins. I've build a prototype and I'm not happy...
Hello, I'm using the nrf52833 dk with nrf Connect SDK v2.6.1. I'm trying to disable the watchdog with wdt_disable() but I keep obtaining -1. Is there any way to disable it...
Hi
I recently had to bring some prototype boards online for the first time, and in this context did i have to flash the modem firmware (v2.0.2 to the SiP (nrf9151).
...
Hi,
I have been debugging with Serial LTE Modem(SLM) without an external flash .
I made the circuit of nRF9160 (SICA) without the external flash (MX25R6435F?) , I would...
Hi All,
I am using nRF Connect SDK v2.7 + VsCode + NRF5340 DK and trying to add and extend matter-light-bulb sample. With ' MA-onofflight ' when I try to compile the project...
