I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello, I am trying to create an application on the nRF5340 which samples data at 16kHz and packages + sends it over BLE. This requires a BLE throughput ~1Mbps, which I can...
I am using MX25 external flash with nRF9160. I am unable to find the configuration to use the Zephyr APIs to access the flash. I am able to access it when I am using
spi_write_dt...
Dear Nordic Semiconductor Team,
I am a representative of ELKO EP company and we are currently in the process of obtaining FCC certification for our products that utilize...
I'm using the nrf7002 on a custom PCB, so its a brand new chip. I haven't done any OTP programming for the mac address and instead it's just a hardcoded mac address that's...
Hello Support Team,
I hope this message finds you well.
I've been experimenting with the LittleFS sample available at the following link: LittleFS Sample Code . The sample...
I am trying to use the UART over the onboard USB without flow-control.
I'm currently using a Seeed XIAO_BLE whose bootloader initializes the USB port.
I have a simple...
Trying to build on nrf51822 with segger embedded studio with soft device
I got the error increasing alignment of section .vectors from 1 to 2 because it contains executable...
nRF5340 SDK 2.6.1
I am migrating a project (based on coap_client) from NCS 2.4.1 to NCS 2.6.1, and I get a compiler error:
The offending code is this:
If I open...
I am a beginner in BLE and I want to use one nrf52840 as host and one nrf52832 as controller to learn HCI UART. In nrf52832 I flash the hci_uart program in the zephyr routine...
Hi Nordic Team,
I am using SDK 2.7.0 & board: nrf52840-dk for matter lock application and facing below issue when boot device.
I want to create factory data manually using...
I am trying to build chip-cert tool with nrf connect SDK. Can you please help me fix this issue:
I followed the instruction given on this link: docs.nordicsemi.com/.../nrfconnect_factory_data_configuration...
HI , currently i am using nrf52840 soft device s140 sdk ver. 17.1.0 i have two controllers i need to transfer the dfu ota file form one controller to other controller using...
Hi i am currently using nrf52840 s140 sdk ver 17.1.10 using central uart and i need to add dfu ota code to it how can i add what is the required files to it we tried these...
Hi All, I am having issue building a project where I am attempting to add a custom BLE service. The error message is shown below along with my relevant project files. Any...
