Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hello,
In the nrf5340_aduio application. I found it support 2 channels both of output(mic signal) and input(audio signal) on the USB device.
But i want to know if it can...
Hi,
I am debugging an application whth MPSL enabled and occasionally get this error:
E: SoftDevice Controller ASSERT: 48, 190
E: ***** HARD FAULT ***** E: Fault escalation...
Dear Nordic team,
I'm evaluating nRF5340 Audio DK for the use-case of broadcasting multiple streams.
Until now I've succeeded in broadcasting 4 streams (LC4 bitrate...
I download urfutil and install the nrf5sdk-tools in the Dockerfile
When running the image locally all is well, the installed commands are found.
But when it is running...
After interfacing my STM32 with the nRF9160-DK board and completing the programming, I now need to flash the board with the firmware update file, application file, and our...
Hi,
I noticed all of your DK have multiple UART over the USB port. I believe some are from the nRF91 or nRf70 etc and some form the Segger module.
For a new HW design...
what is the difference between internal oscillators and external oscillators for nRF52833?
What the functions are affected? can share more details so we can choose proper...
The sample source of unicast_audio_client and unicast_audio_server can be built with VScod or command line, but an error occurs when writing.
The error is as follows.
...
Hello, Im trying to use the Unity framework. I was able to run a simple test, however I would like to change the print function - UNITY_OUTPUT_CHAR . From the nrf/test/unity...
Hi
Is there a way to do this quicker?
I have my own custom characteristics. Is it like bonding will imrpove this? Atleast for the case of a reconnection?
Is it bonding...
Hello,
I am running a simple experiment to turn on all GPIO pins to active on the NRF52840.
The code attached works on the NRF52840-DK, and I am able to measure 3v on...
Just started another project using an nrf52840 dev board, and the printk() call produces no output. There is no output for Zephy booting, or anything else. I have tried both...
Hi,
according to my system architect it should be possible to use a standard https://github.com/NordicSemiconductor/pc-ble-driver on the nRF52840 Dongle for implementing...
Hi guys, I'm trying to measure deep-sleep current of my application quite precisely to obtain a reference measurement to evaluate against for further improvements. The setup...
