I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
The headline says it. I've had this installation about a month and always when I say
nrfutil is taking 100% of CPU. I have up to date ubuntu 22.04 with ubuntu 22.04 in virtualbox...
Currently I'm using nRF52840 and in my application I've defined two GPIOs as an interrupt. one among them is designed such that it changes to output pin, gives a pulse then...
I want to perform ADC high-speed acquisition on IO pins. The solution is SAADC + TIMER + PPI + double buffer. The length of the buffer area is 100. The conversion cycle of...
Hi,
I'm trying to pass audio data from PDM callback function to a USB device and I'm kind of stuck.
Background: I'm using the nRF52840-DK board and 2 MP34DT05-A microphones...
Hi,
The main problem is that I have a problem with NRF Connect desktop to erase/program nrf52840 dk. I get this error:
" Error: Failed with exit code 1. One or more...
Hi,
I'm using nRF52840 DK with ncs V 2.6.0. I plan to create an mp3 or WAV audio player. I tried using the MAX98357A with the i2s nRF52840 DK board, building a project i2s...
Dear Nordic Semiconductor Team,
We are currently working on a project that involves integrating the NRF5340 MCU. After reviewing the MCU datasheet and HW design guidelines...
Trying to use the QuickStart for the Laird Pinnacle DVK. The Quickstart only shows that JLink is detected, but not supported when connected. Even connecting directly to the...
Hi,
I want to get the tick count of the system with sys_clock_tick_get(). I am using a library for NFC reader chip ST25R3916B and provided library from STM requires a platform...
Hi,
I am using https://github.com/NordicDeveloperAcademy/nRF-Connect-SDK-Fundamentals lesson5/fund_less5_exer1 as base. I have set P0.26 as UART RX. Using the code below...
Hi,
We have 3 nrf5340 LE audio dks. Two of them are flashed as BIS gateways.
One as a BIS headset. Sample used: nrf5340_audio in ncs 2.6.0
I am able to stream audios...
Hi! I am taking reference to following issue :
I have implemented same method as discussed in above link. I am getting message on client side successfully only when code...
Hi, I am trying to set up unit tests for a new zephyr project on the nrf9160. I don't want to run them on the device and instead want to run them from the command line.
...
Hi, I'm currently using nrf5340 and central_multilink and central_uart example to build connection between one central devices to several peripheral devices. But right now...
Greetings
I am following along with the nrf SDK fundamentals, where I am doing lesson 3 exercise 1, which is related to printk. I have flashed my nrf5340 dev kit and it...
