Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Now using 52840(S140_nrf52_7.2.0 protocol stack, SDK:17.1.0) Bluetooth packet sending found that the packet sending data length is far less than the actual length to be sent...
I am using a module named MS12SF1 which is a nrf7002+nrf5340 combine module. For wifi initialization, qspi is used. As it wasn't working I added spi4 in the nrf5340dk_nrf5340_cpuapp...
Hi Support Team
If we use nRF52840 develop BLE peripheral base on NCS. What is the maximum number of phones can connect nRF52840 at the same time? Many thanks.
Hello, I'm working on the nrf7002dk WiFi station sample. Most of the time, data is sent and received successfully through HTTP using the HTTP PUT function. However, occasionally...
Hi everyone.
For FCC testing we are required to create firmware builds to transmit at the beginning, middle, and end of the BLE spectrum to allow the lab to verify duty...
This happened last month also during debugging of . I could not use my device for the whole month because the quota was gone in minutes.
Now, new month, new quota, I turn...
Hello,
I am trying to run the asset tracker v2.
I have completed the setup steps and configuration.
Can you please let me know what to do ?
I have read that the -128...
I am inquiring about the ability to run two different radio protocols from a single nRF52840, based on this little marketing aritcle by NordicSemiconductor . Specifically...
Hi,
I am using nrf52840DK and trying to implement a weather station application using thingy53 application example. I am using a Bosch BME280 sensor and could read the data...
Hi, we are using nRF52832 for our project. SDK version is nRF5_SDK_17.1.0_ddde560. SoftDevice is S132.
The project requires TWI to read data from a sensor and send that...
Dear All:
I found that there is a shell interface for the nrf5340_audio project.
I wanted to test the sd card playback from the shell interface.
For the broadcast sink...
I have two nrf9160DKs that are talking to each other over BLE. Things are working fine but I want to eliminate some of the external noise in my environment. Is it possible...
Hi,
I'm using nRF Connect v2.6.2 with Wireshark (3.6) and it is setup with the nRF sniffer + Nordic network keys configured.
I can decrypt packets from another Zigbee...
Basically I want the nrf5340 to reconnect to a paired peer upon reboot. The code seems to suggest that this should happen via directed advertising.
I am testing this with...
Hello:
I am Enrique Martinez. Currently I work with nRF52840 in nRFConnect SDK for VS Code. I have problems with documentation about Multi-Image builds ( https://developer...
