Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi,
I am trying to communicate with Serial LTE Modem application running on nRF9151DK through SLM Shell sample running on nRF52840DK.
I am using nrf connect in vscode...
Hi,
I am debugging a program running on the FLPR core on the nRF54L15 development board. I need to call a static library (. a file) on the FLPR core. I use the project created...
Hi:
I connected PPK II with nRF52DK.
PPK 2 is connected to the PC via the PPK 2's USB Data Power port.
The led of both are ON.
I see PPK2 in NRF CONNECT FOR DESKTOP...
Hello, I am debugging a program running on the FLPR core on the nRF54L15 development board. I need to call a static library (. a file) on the FLPR core. I use the project...
I am working Exercise #2 in Lesson 1 and the Screen shots and notes about using nRF KConfig GUI do not match what I see. I am using SDK v3.1.1.
The view I see when I open...
My product is very similar to the PCA10056 and uses NRF52840 and Soft Device S140. The firmware uses NRF5 SDK 17.1.x.
I am trying to set up a periodic scanning feature....
Nordic support,
We are experiencing unexpectedly high and noisy power consumption when using PWM with nRF Connect SDK v2.9.2 on a nRF52811-based custom board, which is problematic...
Hello, I am struggling to find resources or up-to-date information on how to implement the above with NRF54DK (specifically Ezurio BL54L15 DK). Reference material I have found...
Heey, I'm currently trying to implement a w2812 on my custom nrf9160 board. For this I want to use my SPi bus to instruct the ws2812 leds. Because I've already implemented...
Hi,
We have a design error of not having not updated a voltage divider circuit when we increased the high voltage line in an earlier iteration. The range of the voltage...
Hello,
We have a small number of returns for our product, where the modem has gotten into some sort of strange state, and almost seems like it is unresponsive, or blocked...
Hello, May you please help me to understand how to enable the correct mode for testing. This what the laboratory request - "RF frequency fixing software and guidelines of...
We would like to drive two ps/2 interfaces via nrf52840 gpio pins (i.e., reading the protocol bit by bit, via gpio interrupts). A trouble is that ps/2 is timing sensitive...
We're using two nrf54:s, one DK (initiator) and one custom PCB with 2x antennas (reflector)
I've tried adjusting the samples so that multiple antenna paths are supported...
Hi
I have some questions regarding the 32 MHz crystal on the nRF54L15:
If my firmware is configured to use external capacitors, will the very first crystal startup...
