When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hello,
I am having an issue with trying to install the nrfutil program from this Nordic download page . When I click on the download for the Linux(x64) version of the nrfutil...
I'm not totally clear from the SDK documentation on when I can expect NRF_ERROR_BUSY from sd_ble_gap_data_length_update(). Would it happen in the case where both sides attempted...
Hello,
My peripheral device is nRF52840, central is an Android device, Sniffer hardware is PCA10040 kit.
Using this guide https://infocenter.nordicsemi.com/pdf/nRF_Sniffer_BLE_UG_v3...
We have an application that needs to read device battery voltage and a sensor value every 10 seconds. The ADC is using burst mode and 8X oversampling to take each sample....
I created a new dts folder for nrf5340 appcore. The application works fine on the project, but I find netcore is not working properly. I found that the BOARD_ENABLE_CPUNET...
Hello,
My device is already implementing DFU over BLE and all is working fine. But now, I want to add the update over LTEM (Quectel BG77).
I want to proceed like this...
Basic OpenThread application built for 5340 crashes in net app.
The same application works fine on 21540 (52840 + 21540)
The crash seems to happen when some thread packet...
Hello,
I have 2x PCA10040 dev kits connected via SPI.
Device #1 is talking to a custom board MCU by UART
Device #2 is connected by BT to my android app
The task is...
Hello,
I am planning to use the balun BD2425P50100AHF with the nRF52833. The voltage on the pins BAL1 and BAL2 can go up to 15V.
I am wondering what is the maximum allowed...
Hi,
We have developed an application in central mode using BLE nRF52833 chip running on SoftDevice140 , Version 7.2.0
We now need to add support for FEM nRF21540 ...
Hi,
I am using NRF52840 development kit and I need to modify the PCNF0 register values for our application.
I am developing our application using the sample application...
I have ran the Mesh light demo successfully, and capture the Bluetooth HCI log (*cfa file) from my Android phone.
However，the transaction between my phone and the nRF52840...
Hi everyone,
Not very sure this is the right place to share this, if not, moderator please help me to move it to where it should be.
I just want to share with you a...
Hi, i have two nRF5340 DK that i'm testing with the Thread CoAP client/server samples.
I found out that with the newer DK, both the clinet and server samples work. With...
HI,
I keep working on my new customize board with nrf52833 SoC and now I want to add e-paper screen. There is any examples about adding a e-paper screen to customized board...
