I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi.
I cannot build a ble_app_uart Nordic example that I was able to build flawlessly three years ago and later. I wonder if anybody could give me a clue on what's going...
On Zephyr `2.7` I have following code to setup a SPIM on a custom board: Device tree:
main.c:
Now this no longer works on Zephyr `3.1`. I temporarily tried it with ...
Hello
I tried to install nRFConnect for Desktop, the latest version When I try to launch Toolchain Manager, I get an error "Unexpected end of JSON Input" error message....
Hello,
I works with Zephyr, VCS, SDK 2.0.0
I don't find how to get pin number from the DTS pinctrl .
In this folowing code, I want to replace magic number (uplighted...
Until toolchain update it was working well. But after toolchain update I cant even open toolchain manager . It just shows some exception like " Unexpected end of JSON input...
using NCS 1.9.1 - Zephyr - Segger Studio - sample code: bluetooth / peripheral_uart
I based my project on the sample, modified it slightly and it works well on a board with...
Hi,
I saw here: nrf52840 802.15.4: mlme_start_req: nonbeacon-enabled mode doesn't work
that the SDK-Version 14.2.0 was not compiled to work with non beacon enabled mode...
Hello,
After upgrading to the new version with the help of the migration guide, there is an issue that I could not trace back to any changes.
If I am correct its about...
Im compiling an app in nrf sdk 2.0.0 which works well on the nrf52811
as soon as I add
CONFIG_NRF_802154_RADIO_DRIVER =y
into prj.conf
without even initializing...
Hi Everyone,
I am working on NRF52833. I have developed code for our project. Now in this project the phone app will connect with the device using BLE for which I have implemented...
I have a Nordic Thingy:52 and Nordic Thingy:91, and I want to develop custom embedded software for them. Do I need a J-TAG or can I flash code using USB?
I've seen tutorials...
Hello,
I'm starting development with nordic arm processors. Therefore we purchased the BMD-360 EVK. This board features the NRF52811 processor and has the same pins as the...
We currently have a nRF52840 central device written with the Bluetooth Nordic SoftDevice API. From what I have read, the Zephyr RTOS is the best way going forward. I started...
