Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hello all, I tried installing Segger mebedded studio on a new PC and followed the install steps from the getting started guide. Everything seems to be installed correctly...
Hi there,
we are a student project and are using the nRF51822 Chip with the MDBT40 module. We designed our own custom PCB and followed the instructions for the circuit as...
I have a subroutine that exercises the SPI interface and only at certain points in the code it won't execute the SPI subroutine and goes into the disassembly when single stepping...
SES IDE, nor nrfConnect programmer tool sees the JLink programmer attached to my PC. No "idcode" in SES. No devices appear in Programmer.
Windows10.
JLink_Windows_V764e_x86_64...
Hello,
I am beginner to work with Nordic, I am trying to setup the development environment for nRF5340 Chipset.
For that install nRF Connect Desktop v3.11.0 version. ...
Hi Team
My SES crashed suddenly. When I tick file->nRF Connect SDK Project, It show below error information. I have try to re-install the NCS from toolchain manager. It...
Hi Team,
I have nRF52 DK PCA 10040.
PC: Windows 10 pro
IDE: Keil uVision 5
Working with nRF5 SDK 17.1.0 with S132 soft device .
To execute the code , first i flashed...
Hi,
Zephyr 3.0 , nrf5340 ncs 1.9.1
i can successfully sent data with
this function ;
So it sends 2 transactions without changing cs state.
1byte tx+rx , and...
Hi,Master:
In BT core_v5.0 2.3.5.6.3 Authentication Stage 1 – Passkey Entry, as shown in the figure below
Question: Why does the process loop 20 times, verifying one bit...
Hi,
I have used the nRF Connect Mobile app to connect a BLE device to my Android device. Once bonded, I can receive temperature signals as expected without issue. I can...
Hi,
I am testing MCUboot in nrf52840 DK
I know that MCUboot can image update using slot 0, slot 1, and scratch area
If so, is it possible to update the softdevice(BLE...
Hello,
We are working on NRF52832 + nRF Connect SDK 1.8.0 for our upcoming product. We need to do OTA of our Firmware.
Could you please help with pointing to the right...
Hi Nordic,
We are using NRF52840 and the NCS sdk to design a new product which may have multiple threads designed. And each thread may need to do some BLE operation at the...
Hi,
I'm developing a peripheral driver which involves UART. I encounter an issue I'm not sure how to proceed.
In my design, I have
main.c
device_drv.c
device_drv...
