Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hello,
I have found out that we have shipped one product where NRF_CLOCK_LF_SRC_SYNTH was used together with the SoftDevice S132. I think at the time when it was implemented...
Hai team,
In my application , I am using nrf52832 , application took 26 microamps in runtime [peripheral - I2c] ,acclerometer and ble advertisements],here i need to put...
Hi Nordic,
My firmware is done and v1 beta is release, i will use it to flash my final production first batch with it.
What are the several good pratices to create...
Hello again,
I am trying to use the nordic PPK2 to estimate the battery capacity I would need. I would like to measure for a longer time in order to spot any strange behavior...
Hello,
We designed a custom board with nrf9160 (modem firmware v1.3.1) that runs an asset tracker type application.
The application uses both, LTE and GNSS:
logs sensor...
Hi I am currently using an nRF52840 SoC and I already have both I2C buses in use, as my application requires multiple I2C sensors with the same address. That means I can't...
I'm using SEGGER's SystemView tool to get some insights on my code. I see which interrupt number is activated, and want to figure out which code actually runs.
looking at...
Hello,
I designed my first custom board and I'm happy to have it running. When I developed my test application, I used printk() to send debug information to the console...
I am working with nRF connect SDK with nRF5340DK. I am compiling code using nRF connect (ncs-1.8.0) for VS code with nrf5340dk_nrf5340_cpuapp board.
prj.conf as below, ...
I am trying to store data to the UICR using SDK16, mesh SDK 4.2.0 and the nRF52840 chip.
I want to write to the UICR once on runtime and never again. To avoid messing with...
Hi, all
I have some issues about developing on nRF connect SDK with VSCode:
Go to definition for macro always jumps to the wrong place. For example, BT_DATA_BYTES...
Hi all, I am using nrf52 with Softdevice 113 v7.0.1 and SDKv16 and FreeRTOS v10.0.1 and I am experiencing some issues with FreeRTOS timers expiring earlier than expected when...
Hi again,
A small edit to make this clear: Is it possible to update netcore using a single slot setup
After asking on another thread regarding something similar Simon...
I want to develop a low power device which enables connectivity for reading and writing data to its internal flash. The access should be with NRF_UART application
The access...
