I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I have attached all sleep modes of our controller that i found through forums and from your suggestions.
But my problem is No one of these sleep modes, wake-up through...
Hi,
I am just starting out creating a project to run on an nRF9160 on custom hardware. I have set up a development environment (v1.9.0) through nRF Connect for Desktop...
Hello I use nrf52840 and BME280. I plugged it GND GND SDA 45 (P1.13) SCL 47 (P1.15) VCC 32 (P1.00) I use timer to refresh data and on the first line of the code I init gpio...
Hi,
In the nRF52840 Product Specification 1.7 , page 34 chapter 4.4.1.9 INFO.VARIANT, I read that the hex code of variant "AAF0" is 0x4141 45 30. However the description...
Configuration :
IDE : SES V5.70a
SDK version : NRF5_SDK_17.1.0
Board : NRF52840DK
Hello,
I'd like to use 4 channels of the ADC in a scan mode at a high frequency...
Hi,
I am working on an application to transfer firmware file via BLE-GATT to nRF52833. Can you kindly suggest any sample code for me to evaluate.
Thanks,
Ubaid
Hi,
I've been following this tutorial regarding connecting my BLE device to another Bluetooth module:
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/getting...
Hello,
I have a question regarding NRFX_SPIS_XFER_DONE event. Documentation says that this means "SPI transaction has been completed."
I'm curious if this event is triggered...
Hi,
I have just bumped the NCS I am using for my project to version 1.9.1. After this update, I found a bug in the Zephyr code.
On line 214 of zephyr/subsys/net/lib/lwm2m...
After some advice here, Typically I use the native or recommended IDE's for the platform I'm working with and generally have no issues getting up and running. This time around...
Hi,
I am using NCS v1.9.0 and have a question about datatime module.
It seems to have NTP and Modem clock sources, but I don't want to use either clock source. I have...
Hi
Thank you for your attention to my question, I would like to inquire how to control each channel of hardware PWM individually, We have 6 LED lights, each LED has different...
Hi, I am running Sample DFU app based on peripheral_lbs suggested by nordic on BL653dvk : https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs...
is it possible to transfer my emulated code from the nRF52840 to the nRF 52811? How do i do that? Or a better question; how do i write my code on the nrf52811 using the nRF52840...
I am working from this video:
https://webinars.nordicsemi.com/developing-bluetooth-low-energy-6
Which nRF5340-DK build configuration should I use please?
nrff5340dk_nrf5340_cpuapp...
