When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I am developing an applicaiton to run on the app core of an nRF5340, and I have mcuboot enabled for the purposes of handling DFU.
I have recently implemented signing the...
Hello, I am having a problem with the development on a custon board. During system-off I wake up the chip with nrf_gpio_cfg_sense_input function on PIN 5. The chip wakes up...
Hi
I am designing a new BLE device and have some questions about the PCB antenna.
The product will be worn on the body.
I have a 4 Layer PCB with 1.0mm with and 35u...
Im trying to use the BLE LTE Gateway running on a NRF9160DK
I have the NRF52840 running the lpuart_hci code and that is working fine i can configure the BLE from the NRF9160...
I have nRF9160DK kit. The iBASIS SIM does not work in India. I aaranged a M2M SIM from Voadfone. The Vodafone SIM has 20 digit ICCID printed on it, while the nrfcloud accepts...
SDK version - 15.3
Segger version - 5.42
DK - nRF52840
I'm a beginner and I was following this tutorial our_services . The code given in the tutorial worked for SDK...
Hi
I am testing nRF52833 UART DFU function, but there is an error in merged HEX file,
Parsing input files. Merging file "SD.hex" into output. Merging file "APP.hex"...
When associating a pin with the UART, is it possible to still configure the pin to be open drain and with a pullup, or does the peripheral associating override those sett...
Hi :) ,
I'm using TWI to connect a sensor that i supply with an LDO regulator.
This LDO has an enable pin controlled by P0_23. Driving current is max 1uA so i configured...
In our project, we have defined 5 FDS_VIRTUAL_PAGES each of size 1024 words and have programmed to do GC if > 10 records are deleted. I see the 1st page being used for storing...
i have installed segger ide and nrf connect for desktop for programm nrf9160 , i have successfully uploaded Blinky code (zephyr) .but now i want to create a new project ....
Hi, I am trying the MQTT_SIMPLE sample on both the nRF9160DK and my own custom board. I have mfw_nrf9160_1.3.1 on both nRF9160 and I am using SDK v1.8.0. LTE connection seems...
Hi,
I'm using NCS 1.8.0 on a nrf52840.
I've got what seems to be a corrupted external flash Settings file. The issue doesn't seem reproducible yet, but as it happened...
I am working with SPI for the mfrc522 RFID reader. We were able to read the card previously while we used nRF connect SDK version 1.5.1 and nRF connect 3.6.1
Now I am not...
I'm using modem version mfw_nrf9160_1.3.1
It's waiting for semaphore and when CSCON notification came in between it's just resetting due to some hard fault. Can somebody...
