Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi support channel，
i am testing 7002 dtim current consumption.
and i have set router dtim to 1 second,because AI told me there is no api to fix dtim to 1 seconds.
and...
application : sdk17.1/multiprotocol\ble_ant_app_hrm\pca10040\s332 i want to realize ble dfu on this demo, but i can not find the relevant example. how should i do? best r...
1. Create nRF Connect SDK-based Zephyr freestanding application and work on it for a while but don't push git to any remote.
2. Convert project to Zephyr workspace application...
“Why can’t I light up the LED when using the official NRF5340 Blinky example? During debugging, I found the program stuck at SLEEP_IF_ALLOWED(__WFE); in the cpu_idle.c file...
I have a 2 Mbit EEPROM, normally I would configure the overlay as follows:
But the M24M02 eeprom uses 4 addresses to access 4 blocks of memory within the device, 50, 51...
Hello
I've juste came back from holidays and I no longer can do pristine build on my applications (no matter which toolchain or SDK I am using). When I do pristine build...
Hi,
I'm not sure if this is the correct place to report this, but it was not possible for me to report this on the nrfx GitHub page.
I found out that the function nrfy_nfct_...
I'm using nRF Connect SDK V2.7.0 and want to achieve coexistence between Zigbee and IEEE 802.15.4 physical layer on the same Soc. Is it possibel to enable the MPSL feature...
Using nRF Connection SDK v3.0.2 and nRF Connection SDK Toolchain v3.0.2
Create a new blank application, "Add build Configuration" for nrf54l15dk/nrf54l15/cpuapp/ns then...
Steps Taken:
Followed the official Nordic guide for adding DFU support to Thingy:91.
Built the project successfully using west build .
Tried flashing via...
Hi all,
Full debug builds ( -Og ) of lwm2m_client simply don’t fit into the nRF91xx targets (nRF9151 DK, Thingy91, Thingy91x). As a workaround I found that building with...
Hi There,
I'm following the "nRF Connect SDK Fundamentals" to set the environment up. The device I'm using is nRF52 kit with N52832 MCU and PCA10040.
The USB wire is works...
Hello,
I am following the official Nordic Academy nRF Connect SDK Intermediate course , specifically Lesson 9 – Bootloaders and DFU/FOTA, Exercise 5 (FOTA over Bluetooth...
Hi,
I’m using the Thingy:91X board with the nRF9151 chip, modem firmware version 2.0.2, and SDK version 2.9.0.
We’re encountering a serious issue: the modem does not reconnect...
Hi, I am no longer able to download the nRF5 SDK version 16.0.0_98a08e2 using curl . A few weeks ago it worked fine, but now I can only download the .zip file through a browser...
