I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello,
I'm running Buttonless DFU successfully, but I would like to know if it is possible to start the application with the DFU service disabled, and activate it only later...
Hi, I have a firmware that runs well on nRF52833 dev kit (SDK 17.02) and I am trying to port it to a Laird BL653 dev kit. The firmware has a bootloader and it can perform...
so I use the default sdk in
D:\sdk\nRF5_SDK_17.0.2_d674dde\examples\ble_central\ble_app_uart_c\pca10056\s140
when i press button on nrf52840dk(pca10056)
it should at...
Hi,
I am evaluating the nRF5340 SoC and the recommended toolchain nRF Connect SDK (NCS).
I see that NCS is based on Zephyr RTOS, which provides also some drivers (spi...
Hi! I'm trying to save some variables after a watchdog reset for debug why my application hangs up.
I add a ram section on flash_placement.xml ( <ProgramSection alignment...
I am looking for Static analysis tool ( which is in compliance with standards MISRA-C and CERT-C) to be integrated with Segger Embedded studio.
Is there any preferred...
Hi
I am looking for a ways to perform DFU over serial, surprisingly i dont find any ways except this thread with no answers
https://devzone.nordicsemi.com/f/nordic-q-a...
Hi all:
About with the nrf_desktop example in NCS ,
I would like to modify the CONFIG_BT_HIDS_MAX_CLIENT_COUNT to '2' ,
so I add below command at "app_ZDebugB0.conf...
Can someone tell me the correct cable to connect the two boards together for debugging purposes.
There seems to be two main options, but its not clear:
TC2050-IDC-NL-050...
Hello, I experience some issues with NRF9160 and eSIM card. SIM_1V8 always output 0v and "AT%XSIM?" return "%XSIM: 0". I want to know if there is prior software configuration...
hello all,
I am trying to find the best power efficiency to transferring a pack of data(30 byte each time) from one nrf52 to another nrf52. I have a 80 uA in average power...
Hi all
So i had a working running example on SDK Thread and Zigbee V3.0.0. This flavor used the softdevice s140_nrf52_6.1.1_softdevice.hex I've migrated to the new SDK...
Hey All
I've found thread, dealing with this problem here: https://devzone.nordicsemi.com/f/nordic-q-a/77775/nrf_ble_lesc-nrf_crypto_ecc_key_pair_generate-returned-error...
I try to connect my nrf5340 CoAP server via my border router with CoAP Messages (with the IP address) from a computer. Is that possible? And if so, How?
I made a border...
