Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
NRF52833+SDK17:
I want to use the saadc to sample a DC brushed motor running current when pwm at rising edge, pwm driving the motor.
I can't understand the real meaning...
Hi, I've been working on SDK v1.6.1 and I just wanted to try the v1.7.0, however some functions on the power management have changed, in particularly:
int pm_device_state_set...
I am encountering a problem with programming an nRF52840 DK:
1. I've installed nRF Connect for Desktop version 3.7.1, nrfjprog version 10.14 and Segger JLinkARM.dll version...
Hi,
I'm using the CLI and have logging enabled. The only way I'm able to see my logging output is if I type "log enable info" at the CLI prompt.
Is there a way to enable...
Hi to every one,
i have some questions, I need to be able to update the device to the new firmware, update to the old version and update to the default firmware. for this...
I am connecting the nRF52 DK to an oscilloscope and on the LED pin for the dimming example on the server side. I am seeing jitter, the PWM duty cycle doing a slight shift...
HI
Now I am measuring current on the nRF9160DK according to https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/hardware-design/posts/getting-started-with-current...
Hi,
I have nRF52840 DK, and using nRF SDK v17. I am trying to understand radio transmitter example sendpacket().
RTC(1) seems to be used to the transmitting packet.
...
I have designed/copied the suggested circuitry of the nRF9160. I am attempting to program the custom board through a nRF9160DK. It is connected and the command west flash...
Hi,
I am using NCS 1.5.0 and modem firmware 1.2.3.
In my application I need to receive few commands from PC UART (UART 0).
Baudrate is 115200 without HW control. ...
Hello,
I am currently doing an internship and I am working with the nRF5340 DK.
Until now I have tested the "Thread: CoAP Server" and "Thread: CoAP Client" examples and...
Hi my application is working fine with secure bootloader on devkit PCA10056 using nRF52840 and GCC. Now I want to bring it to my target hardware using nRF52820 to get rid...
Hi,
I am writing my own SPIM driver, when I try to send a 2 bytes message and then a 26 bytes message the second message "crashes" after 2 bytes.
But if I send the 26...
