When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi, I am working on my custom made board, and I use P09 and P10 as digital outputs. I am aware I should disable NFC by adding the preprocessor: "CONFIG_NFCT_PINS_AS_GPIOS...
Hi All:
As the topic...........
1.what is the relations between the HID descriptor and data IN/OUT buffer?
2.Is the USB generic HID receiver_Function and tansmit_Function...
When launching the nRF9160, the following error occurred: <inf> at_host: UART check failed: 12. Dropping buffer and retrying.
Under what conditions does this come out? ...
I am trying to add DFU to my project, so I merged in the code from the example in the SDK as follows:
I included the same .c files as the example project
I copied over...
Hi,
I did some measurements today on our I2C bus and see that the GND level is different some times. The most time it is not GND level (about 800mV). I checked cross talk...
Dear
I increated a Generic Level module to main elements which have a Generic ONOFF module on Mesh example Light Switch Server project base on PCA10056 DK board for nrf52840...
Hi I am using the example code here https://github.com/NordicPlayground/nRF52-ADC-examples/tree/master/nrfx_saadc_simple_low_power_app_timer_multichannel_oversample to use...
Hello guys,
Has anybody had the issue opening the new version of nRF Connect for Desktop (v3.6.1) in Windows 10 Pro. I have used an older version of this application and...
I want to build a secure boot loader for my custom board based on the nRF52832.
This post claims to walk through the process of building an example of a secure boot loader...
I'm strugglgin to find any documentation on how to set/request the iDRX paging interval in RRC idle. I have a device which sends an MQTT keepalive message every 3minutes,...
I have run into the issue where the soft device is not being processed when I debug so it throws the assertion failed error. After a lot of searching on the forum I came across...
We are using FDS from SDK 17.2.0 on nRF52832.
It is working so far, we can store and read back data.
When putting battery in and out fast, we get sometimes, but often...
I have the thingy52.py script running on a Raspberry Pi 4, and I can successfully poll the sensors when the Thing52 is awake (recently tapped) but when I try to poll in a...
In our final product, we wish to send the battery voltage level with other data to our server so that our customers can see how much the battery is drained. I am seeing that...
