When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I am using Meander line inverted F antenna for beacon and development board based on nRF52832.
Is it okay to go with this antenna or shall i change this antenna.?
Where...
I have a custom PCB using the nrf52832. when flashing my PCB or connecting to the RTT terminal, pins SWDCLK, SWDIO, VDD & GND are used. i would like to know if theres a way...
Dear Sir/Madam,
I want to test the BLE 5.1, Aangle of arrival (AOA) and angle of departure (AOD) feature. Kindly guide me which of the example of sdk 15.3.0 is useful for...
Hi all!
I am working on the SDK 15.2, with S132 6.0, and i use the SES IDE.
I have created a custom service with 32 characteristics for now. The goal in the future is...
Hello All,
I want to write codes for all the peripherals like GPIO , GPIO with Interrupt ,UART ,UART with interrupt , I2C , SPI , All Timers..without using the drivers provided...
Hey! I am testing some power consumption of my application, and I need to have a long rest period of appr. 15 minutes. I'm using an RTC timer in System ON sleep mode, full...
I have made a bluetooth beacon based on nRF52832 chip. I am able to write code DeviceDownload\nRF5SDK17009d13099\nRF5_SDK_17.0.0_9d13099\examples\ble_peripheral\ble_app_beacon...
Can i use 2 nos NRF52832 BLE chip on single PCB , PCB size is 30x50 mm ,
1 chip for scanner
2 for advertising
3.If yes what is the position for antenna of both Chip...
Dear technical support.
We are using this chip (nRF52832) in our hardware.
I'd like to check is this feature AoA(part of BLE5.1) enabled in the chip?. Is there any application...
We are designing a people location tag for building workers. Bluetooth direction finding AoA/AOD is good for the application. Is there any development broad for Bluetooth...
There is a potential for the NRF_MESH_ASSERT(m_reliable.next_timeout_index < ACCESS_RELIABLE_TRANSFER_COUNT) to fire on line 170 of access_reliable.c if the following conditions...
Hello,
I am trying to install the pc-ble-driver-py for my buildroot arm-board.
After some struggle I was able to compile the pc-ble-driver for it, however the python tool...
Hi guys,
I am working on my project and until now I enabled the device to measure the voltage and get the sensor data from the temperature sensor which I need now to send...
Hello,
We have been using FDS in our nrf52832 based product. Recently we had a need to port application to nrf52810. It required some flash memory optimization. Fortunate...
