I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I looked at the following question
nrRF2 GATT attribute read callback
and it does not quite answer what I want to know.
What I need to know is do I get signaled by the...
I have followed the getting started, with my new nRF52840DK, with switches at:
Sw6 Default
Sw8 On
VDD selected
when plugged into the USB, LED 5 blinks rapidly, LED...
Hello.
In order to connect multiple units on the previous question page ( https://devzone.nordicsemi.com/f/nordic-q-a/51970/implementing-multilinks-on-multiroll-programs...
I want to develop our PC software to control the USB nRF52840 Dongle to be as a BLE central device，so I need to know the command that the nRF Connect used to do this，but I...
HI as i am new to nrf nordic semiconductor development i have some quetsions regarding application im developing
I am trying to develop Ble application where nRF 52 will...
Hi,
I am trying to add DFU service in ble_beacon example. I am using SDK14 and softdevice is S132_5.0.0 for 52-dk.
I have merged dfu example with ble_beacon and initiate...
Hi,
For my application using softdevice I need ADC update every 400ms and Battery level update every 2sec and string update for HT1632 led driver every 2sec.So I have created...
Starting with the BLE Uart Service example code, I wanted to send longer length packets, so the necessitated modifying settings like NRF_SDH_BLE_GATT_MAX_MTU_SIZE, NRF_SDH_BLE_GAP_DATA_LENGTH...
I can power nrf52832 using USB without any issues.
I see a strange behaviour using external 3.3V adapters. The chip does not turn on. The power supply to the chip is available...
Hi,
I am working with relay example .I want my android to send data to the relay board .In which function of the relay example should I make the changes or will i need to...
I've being haven troubles getting to run SES examples, it keeps falling, is probably path problems but i can't indemnify them. So i want to start all over again from nerf...
Hello,
I have a question regarding power - up sequence of NRF52840.
When the USB is plugged in, the VBUS voltage is at 5V.
However, at the same instant, VDDH is...
I have a nRF52840 Dongle that connects to a USB port on my computer. I have a device that can connect to it via BT and the readings are logged through the Nordic utility app...
