Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi, thank you for looking at my post.
I am using Keil V5.25.2.0 with a nRF51422. I am using the soft device "s310_nrf51422_1.0.0-2.alpha_softdevice." My memory regions for...
So, currently I utilize DK's to program and debug both pca10040 and pca10056 utilizing a custom shield that plugs into any of the nRF52 DKs. The programming and the debugging...
I used SDK15 and ble_app_uart_c.
I start a UART timer sending and start a LED timer. There is a probability of app: SOFTDEVICE: ASSERTION FAILED in the process of running...
Hello all,
I'm using the Nordic SDK 14.2 BSP button handler. I have a push, release, and long push event on a single button. These are working as expected -
Except when...
Hi all
I am using the spi0 to storage the data and twi0 to get sensor data . But after I add the file nrf_drv_twi.c and compile , it complies wrong :.
\_build\nrf51422_xxac...
I have problems with disconnecting my Android devices from my BLE peripheral. I don't think this is Nordic-specific, but perhaps someone has an idea?
Disconnecting using...
Hello,
i have a application with two operating states state1: device is in deep sleep state 2: device is running
i wake up the device from deep sleep via gpio interrupt...
Hi
I am integrating your Android DFU library with our mobile app to do FOTA to our Nordic device nRF52832 . We are using SDK 14.2 and doing the firmware update using zip...
I have the nRF51-DK and have installed Python etc. and the nrf_sniffer_2.0.0-beta-1_51296aa.
3 .hex files are in that installer: sniffer_pca10028_51296aa.hex, sniffer_pca10031_51296aa...
Hello,
I'm trying to shutdown my whole system (nRF 52832, SD132, SDK 12.3) after advertisement fast and slow are finished, following the structure of the peripheral BLE_APP_UART...
Hi,
I am trying to run lightswitch example in MDK.
Provisioner keep logging : 419, Unhandled Mesh Event: 4
Button 1 is in on state.
and LD5 is keep blinking.
these...
Hello. I'd migrated my application on SDK 15.1 from 14.2. The firmware of my product is always updating so I use NRF LOG module to debug it and see what is going on in every...
Hi to all,
recently i bought PCA10059 board, but i have problem in programming it. because i had some experience with NRF51 and NRFGO, at first when received the board i...
Dear Nordic,
I am using nRF52840 chip for BLE Advertising I want to encrypt this Advertising
I Read a CCM-AES encryption in BLE is it right way to this 31 bytes advertising...
