Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi,
We are using nRF Connect for Desktop as the production fixture to test the BLE function of our products. To automate some testing procedures in production, we want to...
The advertising PHY is set to 1M; is it fixed? If so, I'd like to understand the reason by reviewing the relevant technical documentation. In the example, it is set to AUTO...
Hello.
I have an nRF9160DK and an nRF7002DK. My goal is to set the nRF9160DK to use the nRF5340 as a module to connect to Bluetooth.
There are two main things I want to...
Hello,
I am considering implementing SPI communication as the transport layer for mcumgr in my application. The setup involves an nRF52820 as an SPI slave and an nRF52840...
Hi everyone,
I am using the S25FL064L memory with the nRF52840 microcontroller and I have a reading problem.
I can read the memory using READ4O mode (opcode 0x6B) but...
Hi Nordic Team,
I'm trying to enable modem tracing on the gnss sample code on my nrf9160dk but have been getting the following error:
Per suggestions on similar threads...
Hi All.
Regarding this exercise, are we sure there is no bug in the https://academy.nordicsemi.com/courses/nrf-connect-sdk-fundamentals/ documentation?
After installing...
before setting NRF_POWER -> SYSTEMOFF = 1, I chose a switch button and an accelerometer as external wake-up sources.
both of the wake-up sources can wake up the chip in...
Hi,
I have an application called `main_repo` built using v2.1.1 (the SDK version doesn't really matter). This contains all source code, dts files, Kconfig files, etc. to...
hello Nordic
trying to migrate from ncs 2.5.0 to 2.7.0
well i did the mistake of installing the toolchain via the vs code .. for some reason it installed it in the wrong...
DFU is now implemented on ipads and iphones, as well as on Android phones, and the app platform is nRF Connect. The problem is that the firmware upgrade can be achieved normally...
I was trying to build off of the example of Lesson 6, exercise 3 from the Intermediate course on DevAcademy.
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate...
Hi there,
I am trying to interface SPH0465 microphone with nRF Dev Kit 52832 with the following configurations of I2S:
I have followed the code from echo example...
Hello!
I am hitting a really frustrating issue running Zephyr on a XIAO BLE Sense module which is based on the nRF52840 MCU. I am simply trying to verify development setup...
