I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I’m developing a product that uses the nRF9160 for LTE-M and the nRF52840 for Bluetooth. The nRF52840 is a pre-certified module, and I have experience with FCC compliance...
Is there any hardware limitations that would prevent one from using the nrf_802154 drivers on an nRF9161? If no, could you adapt the open-source sl to use the 9161 modem instead...
Setup: custom nrf9161 PCB, flashed with nrf9161 modem fw 2.0.1, using NCS 2.6.1
Targeting my custom board, I couldn't even speak to the modem lib, no IMEI etc.
So I dug...
Hello,
I have been trying to correctly setup my nRF Connect inside VS Code.
When I try to execute the command
west -V
in a nRF Connect window inside VS Code, I...
Hi i am using nRF52840 with segger embedded studio.
SDK -> nrf5-sdk 17.1.0 I want to configure rtc2 so that whenver i initialize it it should generate an interrupt after...
Hello, I am building a device which simultaneously advertises as a beacon and acts as a peripheral role device. Advertisements are sent at ~20 Hz with the connection to the...
hi:
I am use broadcast_sink and broadcast_source of nrf5340_audio simultaneously. use a button to switch source or sink. i am use NCS v2.6.2 if switch to sink mode is show...
Hello friends, I am using nrf52833 MCU for my current project, this project involves a sensor from infineon that operate on SPI and it supports high frequencies up to 50 MHz...
Hi,
I referred to the DevAcademy FOTA over Bluetooth Low Energy, but in the provided code, the BLE mobile app connects to the device and it automatically enters DFU mode...
on cannot connect to the on-board Jink of the NRF52840DK board
I have tried:
Updating to the latest Jink driver
installed nrf connect tools for windows
connecting...
Hello,
I'd like to develop a BLE OTA Bootloader using the NRF Connect SDK, but I need to program my NRF52840 with a Serial Wire debugger. What tools do I need? Is there...
Hey,
Im have a thingy91 and multiple nrf52840 pcbs.
my goal is to make the thing91 a central device that reads data from the nrf52 devices and sends it over to the cloud...
We have a custom board with an nRF7002 controlled by a non-Nordic MCU. The WiFi drivers were ported from SDK 2.7.0, and WiFi in general is working, this question is about...
(I am a beginner) Hello, I recently got the Nordic nRF52840 dongle so I can sniff BLE packets from some devices I have. I set up the dongle following the recommended setup...
Hi,
What is the voltage on nRF52811-CAA chip DCC pin (A5)?
Can the regulated voltage on this pin be used as a voltage source to supply some external circuits?
Please...
