I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
Hi,
I am facing a power consumption issue with the nRF54L15 (BM15C SoC) in deep sleep (System OFF / low-power state). The measured current consumption is approximately 221...
Hi all,
Note that I am using a Fedora Workstation VM on VirtualBox for keeping everything clean. I pass the connected USB development board to the VM. I am trying to evaluate...
Hi ,
I’m working on an nRF5340 using nRF Connect SDK v2.7.99-cs2 . BLE security is configured as Just Works (Security Mode 1, Level 2) on the peripheral .
I’m attempting...
I am using the nRF54L10 on a custom board with a couple of LEDs, a flash storage device and a GNSS device. The application wakes periodically to gather fix information from...
How can I detect when no SIM card is inserted at startup? The purpose is to operate without a connection if there is no SIM card.
[Environ] nRF Connect SDK v3.2.1 nRF9151...
Hello,
I was learning about how the bt_conn references work, how to obtain them and free them, and where they are generated.
I was looking at the central_gatt_write...
Hi
I have currently claimed devices in my nRFCloud I registered two years ago. It looks like this:
It has the mention "powered by memfault" . This is also the nRFCloud...
Hi,
i'm learning l4/e1 and i'm trying to buid the process after finishing step 10 but the build didn't goes through successfully. i got this errors
my SDK & toolchain...
Hello all,
I have an nrf54l15 on a custom board, I am having issues getting a reliable SPI clock signal when using BLE advertisements
This is the clock and correct...
I bought both nrf52 DK with nrf52832 and ISC-nRF52810-A module. I use Visual Studio Code with nrf SDK + toolchain. Hardware connection from ISC-nRF52810-A to nrf52 DK is as...
The openthread coprocessor sample in sdk v2.8.0 and v3.1.0 work for me with the openthread border router but not the sample in sdk v3.2.1
I followed the instructions for...
Hi,
i'm learning the exercise1 for AT commands to control modem and when i apply this command AT%XMONITOR i get the output as %XMONITOR: 5,"","","24202","0901",7,20,"02024720...
nRF52810 program execution failed the CPUID verification. Hi everyone, I have a question. I have a working PCBA with an nRF52810 as the main controller. When reading the CPUID...
