Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi. I am trying to start programming our own development desk with modul ACN52840 (SoC nRF52840). I can provide schematic of development desk in private message if needed...
Hi,
I am develloping advertising configuration and would like to use the fast or slow advertising mode.
In the ble_advertising.h, it seems that the limit are an uint32_t...
Hi,
I am performing several "mlme_reset_req()" on a nrf52840 during runtime without problem, for the most part.
However sometimes the radio stack will stop after a ...
Good day
I noticed that the NFC tag reader sample is not compatible with the nrf9160K. Is there a reason for this ? will development be possible?
Thank you!
Hi Nordic
I downloaded nRF5340 DK Hardware files (Altium Designer files).
pca10095_sheet1 and pca10095_sheet2 can be imported in PADS logic tool.
But, files from sheet3...
Hello,
I have a problem when I send data with CDC ACM and using CLI interface my data is mixing. If I put a delay between sending data I have no problem but this solution...
Hi, I want to enter the NRF52 into a standby low power mode.
I am running sdk17.0.2, with FreeRTOS and softdevice (7.2)
The steps I take are:
1) stop all my threads...
I'm trying to integrate the following driver into my project
https://github.com/nobodyguy/HX711_zephyr_driver In order to load it I need to update the west manifest. Using...
Hello,
I am working with the nrf52840 chip, and would like to store a serial number on the device that persists across boots and OTA-DFU. I have integrated the nvs sample...
Dear All:
We run a simple message model in light_switch_client and light_switch_server code.
After provisioning the two nodes via nRFmesh app and set pubilsh in clent...
Hi,
We need to refer detailed documentation & implementation for health model struct bt_mesh_health_srv_cb
we referred to this document - https://docs.zephyrproject...
Hi, This appears to be similar to Case 232209 (from 3 years ago).
What: I am looking to have the 9160 act as a producer - sending ANT and GPS records on a regular basis...
I have a problem to advertise a service. When I include a header file, an extra service is automatically created. It seems like that the service will be advertised twice....
Hi,
I managed to do a DFU with an application on a nRF52820. Now I wanted to test if I can also update the softdevice. For this I read the following article: infocenter...
