Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hello all!
looking at the nRF52820 module to develop a BLE mash app, layout, however, I am not sure, are the GPIO ports freely assignable on the nRF or are they fixed? Looking...
Hi,
We are developing a product with the nrf5340 and an external QSPI FLASH which contains bitmap images for display rendering. We noticed the nrfx qspi driver incorporates...
Currently I am trying to adapt the Radio Test example to function on our custom hardware which uses the nRF52840 SoC. We need the Radio Test firmware to give access to the...
Hi,
I'm trying to get up and running using the PMW3360 sensor driver ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/drivers/pmw3360.html ) using the NRF52840...
Hello everyone
I would like to know if it is possible to connect more than 64 ble devices through a mobile phone？Looking forward to your reply thank you
Hello everyone
I would like to know if it is possible to connect more than 64 ble devices through a mobile phone？Looking forward to your reply, thank you
Does nRF52832 support multi-pairing? if then, how many pairings does it support?
We use S112 (peripheral only) or S132 (central and peripheral).
BLE device <-----...
Hi there,
I am wondering could the nRF sniffer follow a connection of two nRF Connect SDK built applications?
What I got is like the following:
After some searching...
I've been building a test application, and it's gotten bigger and bigger over time. Everything compiles perfectly. I'm building the ns version for the app core. nrf5340dk_nrf5340_cpuappns...
Hi,
I'm confused about ESB settings. I'm trying to renew our board with new nRF520840 chip and we must need to provide backward compatibility that the existing board has...
Dear,
I use NRF connect for VScode and I installed SDK V1.8.0 with the nrf for desktop toolchain manager application. The hardware I use is NRF5340. I want to use pin...
According Power Profiler Kit II - Quick Start the PKK2 is connected to the nRF9160 DK with
PPK2 VIN to P24 VDD_nRF
PPK2 VOUT to P24 VDD_nRF'
PPK2 GND to P28
...
Hi there,
it is a few days that I try to compile an overlay to manage a Microchip CAN device MCP2515 but I have compilation errors.
I should test the device on a 52840DK...
Hi Team,
I am working on NRF52832 based on the BLE mesh protocol here I am using the Light_switch example of SDK - nrf5sdkformeshv500src
I have a basic understanding...
Hi,
1. Please provide me with an example in which UART0, UART1, uart2, and uART3 are enabled
2. The sending and receiving rate of each UART must reach 1,000,000 baud rate...
