hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hi,
I just go a question about when to use the nrf_moden_lib_shutdown(). Is it necessary to use in this code case? Since I've used lte_lc_power_off().
Regards,
Elia...
Hi
1. I tested function NRF_LOG_INFO and found that NRF_LOG_INFO automatically prints the \r\n character
2. How can I remove the \r\n character
Thank you for all...
Hi ,
i am able to find the api related the reset cause" hwinfo_get_reset_cause". But i need to check this api for the Brownout reset ,Poweron reset and Watchdog reset...
HI,
I need to understand the working of USB RNDIS and how zephyr is supporting that feature. Do we have any documents or example for the same ?
Currently I have BL653_dvk...
Hi
how can i display application logs after merging application and secure_bootloader
the secure_bootloader souce I used is \examples\dfu\secure_bootloader\pca10040_uart_debug...
HI,
I am a newbie with NORDIC semiconductor.
I am working with nRF52833 and working on NFC reader with PN532 using I2C interface.
I can find libraries with SPI and...
Hi,
I have a PCA10095 and a PCA10040 where they are connected via USB to PC and are not being seen. In both cases the LED next to the interface MCU is flashing rapidly;...
I'm looking at the ZBOSS for Zigbee IAS Zone example , and in the " ZB_ZCL_DECLARE ..." statements it refers to structures such as zone_attr , poll_control_attr , and pwr_cfg_attr...
For nrf52x, a pin can be dedicated for reset, and this is from my understanding how HCI works in the sample (host line to controller reset pin). However, for the nrf5340,...
I am doing ble beacon device communication. I have two device, receiver and transmitter. Receiver device height is about 2 meter. Transmitter device on the ground. The distance...
My project builds fine in versions previous to 2.0.0. However, in 2.0.0 I'm getting an undefined reference. Any ideas where to look to track this one down?
/opt/nordic/ncs...
I am in the early stages of development and would like to proceed with only non-secure partitions on the nrf9160. I'd like to not make use of TrustZone.
I notice all of...
Hi Nordic,
I want to use an Arduino USB host shield with NRF52840-DK. Since the VDD on DK is 2.5v and MAX3421 on the shield works with 3 to 3.6 volts, I have to use an external...
