Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Rookie question.
Finally I put my ble working passing a number thanks to the support from this forum. But now my problem is how to send a string with around 100 characters...
Hello nordic team, Question 1 How can I customize the Asset Tracker v1 to send Asset Orientation "FLIP" in the same frequency as the temperature and the rest of the values...
When communication fails on NRF connectivity dongle (In Python via pc_ble_driver) and Error code: NRF_ERROR_BUSY is received on attempts to write and one restarts python script...
Hi,
I am following below link for DFU over BLE. Link ( https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs-dfu ) currently it is working fine...
Hello ,
I'm using the libuarte library so i can send data and receive it , i'm enabling RTC2,TIMER1,TIMER0 and TIMER2 .
this is the main definition of my libuarte NRF_LIBUARTE_ASYNC_DEFINE...
I'm running into an odd problem with the PWM driver. We're using SDK 17.0.2 and the S113 softdevice on an nRF52833. We're using the PWM module to drive some LEDs.
The nRF52833...
1. nRF Connect SDK v1.9.1
2. Segger 5.68
3. sample name : multiple_adv_sets
I am developing through multiple_adv_sets.
I want to test by changing the uuid in uuid...
Hello
I have installed NRF Connect for Desktop in my system (64bit, i3 CPU). I want to debug my custom hardware using the nRF9160 Development Kit. I have connected the nRF9160...
We have a big application bigger than 500ko and we need a littlefs partition, so we end up with a mcuboot_secondary smaller than the mcuboot_primary (actually we put it to...
Hello, as stated in the Titel im trying to read Firmware Information, for Example the Firmware Version. I tried solving this by reading via Flashareas but no matter where...
Hi,
Datasheet says the sequence as mentioned below,
But the code given in the nordic playground does not follow the sequence mentioned in the datasheet, and the code...
Dear members, with success I implemented the time synchronization example from the nRF5 SDK guide. This example works perfect for a single master, but what if the master changes...
Hi Nordic:
How to use GZLL in nRF52833.
It is only has PCA10040 and PCA10056 In "gzll_ack_payload", but nRF52833 is PCA10100.
I try to use PCA10040 run in nRF52833,...
I start learning open thread in nrf connect SDK using nrf52833, it was pretty fun examples. Now I switch from using cli to send udp from/ to devices to implement it in the...
