Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
Dear Sirs,
I am writing you to inquire about following questions about nRF5340. Especially,regarding the configurable bitrate for the LC3 codec in nRF Connect SDK Ver2.8...
Hi
in my application, I need to reduce /disable RAM sections in nRF54L15 to save Idle RAM current. For Example, I need to retain only 64KB RAM when I am in idle.
how can...
Hi folks,
I'm attempting to program an nRF52833 using a Segger J-Link+ connected to the SWD program/debug pins on the board.The board is only an nRF52833 - as a learning...
hi, noted a few things in the Rev 1 Errata v0.8 that might be tricky to solve practically in sw/hw
3.16 [33] RADIO: GPIOs can exhibit radiated emissions
max...
I'm currently attempting to register a service and it's subsequent characteristics statically using variables and not hard coded GATT tabel , I can successfully register an...
Hello,
I've been playing with an nRF54L15 PDK, specifically with the sid_end_device sample. I was having a lot of trouble getting the device to register/connect to Sidewalk...
Dear,
We have project using normal advertisement (not extended) on a nrf5340 module (Raytac MDBT53-1M) to send data using Manufacturer data.
We have a product already...
Hi, Currently Im developing on a custom board that has a NRF52840 and a NRF9160. Both MCUs communicate using UART Async API and I added the support for LPUART on both sides...
Good day, I'm trying to use pin 1.02 as a GPIO in a TF-M build using a (custom) non-secure board target, and I'm struggling to find the appropriate way to accomplish this...
Dear Nordic Team, we are using the adafruit_feather_nrf52840 and nrf52840dk for our prototypes and recently the toolchain around nrf and zephyr has become a problem. Build...
Hello, I have two nRF35340 DK. One of them can be flash successfully, another one always encounter this issue:
I have tried
nrfjprog --recover -f NRF53 --coprocessor...
Hello,
I'm starting to use the PPK2 to understand the current consumption of various IOT products. I have a question about what happens in amp mode should a dead short fault...
Hello.
I am developing using nRF5340DK and nRF Connect SDK v2.9.0. However, this PR has been applied. I connected one smartphone app and two boards(nRF5340DK) to the mesh...
Hello everyone,
I am developing a project where I need to perform bluetooth OOB pairing using an NFC reader. I have a couple questions about this.
The first is, what options...
Hello,
I am using the "peripheral_nfc_pairing" example to pair my nRF52832 in the ANNA-B112 module with my iPhone XR. Currently, the example does not work with my iPhone...
