Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
which pins can be used as PWM output pins in nrf52811.
Can I use them directly or I need to add some hardware to use the PWM feature.
I have an NRF5811 SOM (EYSNCNZWW...
Hi Sir/Mdm, I want to use 1.54 inch e-paper module from waveshare with nRF52840 dongle with Zephyr RTOS. I have read the documentation from Zephyr about the display and noticed...
Hi,
We use the nRF52840 and have now run out of space using debug mode compilation (using CMake from bash).
When we compile in release mode, we get 50% full flash, so...
Hi,
I am using nrf52832 and mesh sdk 3.1.0 with nrf5 sdk 15.2.
We use dual bank approach for our firmware update with the normal nrf5 sdks ble bootloader. But now our...
Hi.
I have been trying to implement my own Model into the Light Switch Example (Mesh SDK 4.2, SD s140 7.0.1, Hardware: nrf52840 DK), according to this Thread:
Adding Simple...
I'm implementing the WS2812 driver on custom hardware and have some confusion around the hardware tuning parameters for the SPI implementation. The description of the device...
Hi everybody,
We ran into a Zephyr configuration issue which is related to Zigbee and Zephyr's networking stack. In our setup we would like to use Zephyr's modem library...
Hi,
I have nRF52840 DK, for nRF52 series devices. I switched from nRF52 SDK to nRFConnect SDK.
I reviewed
http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
Hello,
I am running ble_app_beacon demo from nRF5 SDK 17.0.2 on nRF52 DK and would like to decrease power consumption as much as possible. From this post , I have seen that...
In the official development board directly burn SDK routines, input the command to write data in the serial port, if you continue to input, for example: interval 1s to write...
Hello everyone:
We use NRF52840 to test the transmission function of mesh and verify the minimum publish(client)-->prescribe(server) time;
The following is the publish...
Hi,
I have nRF52840 -DK boards.
I was using nRF SDK (SoftDevice ) to program nRF52 devices. Now I am switching to nRFConnect SDK. nRFConnect SDK is new to me. A few questions...
hi，
My application MTU exchange is 23 bytes，I send data using Notification or indication to sent 105 bytes date，I subcontracted the data into 20 bytes ot sent，How do I make...
