Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hi Everyone, I'm trying to pair the nano leaf bulb using matter chip tool via Open thread border router. I need some help on how to use chip tool to commision the matter device...
Hi,
I am developing an application with the nRF5340 microcontroller.
I need to use the I2C module, but if I insert the CONFIG_I2C=y configuration in my prj.conf file,...
Hi,
I want to weld my product that contains NRF52840, using an ultrasonic welding machine.
Currently I'm thinking of a welding frequency of 20KHz or 40KHz.
1. Is there...
I am currently working on a NINA-B4-TAG from ublox, there is a requirement to be able to dynamically turn on and off the CTE without completely turning the advertising off...
I am thinking of using nRF5340 Audio on a development board.
The I2S-compatible IC on the headset side is an IC called AK4432VT.
The following settings are required to...
Hi,
We have a nrf5340 module on a custom PCB that is connected to a computer through use of a pcie header. This PCIE header allows USB communication to the module and supplies...
Hi,
In my project I need to send maximum bytes possible inside one package. When using the nrf connect app I can see that when reading the characteristic this works, but...
Hi . I have two questions about the PIPEs in Zephyr RTOS , especially regarding the correct use of the k _pipe _put and k _pipe _get functions :
1 ) In both functions ,...
Hi,
when I configure CONFIG_BT_SETTINGS=y as I want the device to remember the pairing parameters, the services defined with BT_GATT_SERVICE_DEFINE dissapear.
As far as...
Hi,
I use nrf52833 running ncsv2.6.0,
I trans v2.6.0\nrf\samples\bluetooth\central_hids to \ncs_v2.6.0\v2.6.0\zephyr\samples\subsys\usb\hid and now plus usb to nrfUSB...
How do I switch nrf52832 from a broadcaster to a peripheral with a service via a keystroke interrupt? After trying it out, I found that my problem was mainly: I didn't know...
Hi,
I'm trying to control nrf9160 SIP from stm32 MCU via AT Commands. Should I program on the nrf9160 the AT_CLIENT sample for this purpose or is not neccesary?
I'm trying...
Hello Team, We are currently working on a project for interfacing Larger TFT LCD display with Capacitive touch with nRF5340 Devkit board and SoC. As per the datasheet of the...