Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi team,
I am building AWS IoT client based on NRF52833 + Ethernet Controller.
I have done connecting and subscribing/publishing to AWS IoT broker successfully, and...
Hi there,
I am trying to set up a BLE communication between a central and a peripheral. For this I have succesfully used the nRF RSCS example from Nordic. But the problem...
hi dev
I'm not sure about beacon, so I'm posting questions to check.
General Ble process is like that
1) peripheral do advertise. during advertising interval, it sends...
Hello,
I was using NCS 1.7.0 and developed MQTT and SPI slave based sensor monitoring system using nRF9160 and want to switch NCS to latest build (2.2.0). A whole lot of...
Hello
Im traying to test the csense drv example , I want touch pad button only one
if I want to use this configuration
put the USE_COMP == 0 to USE_COMP == 1
now...
Hi,
We are working on creating a custom board configuration for ease of development. This is based on UBlox BMD-350-EVAL10. Which uses nRF52832.
While I created a custom...
Hi, I am trying to measure a sensor once a second. I require to use oversampling to get 14bits of resolution to meet our target. We are observing a large step in values that...
Dear all,
so far, for my external SPI NAND Flash memory chip development (Micron 256MB SLC NAND), I have been writing and reading data with my own, very basic level, flash...
I'm getting this error when I try to init the UART:
I have app_uart.c in the project, but a little investigation shows that it's not "enabled" in sdk_config.h.
When...
My current project is based on nRF52810. The nRF Connect SDK I found gives the idea that the architecture only works with GCC, according to the link https://developer.nordicsemi...
Hi,
I just bought a new PPK2. After installing "nRF Connect for Desktop", when I plug USB into PPK2, Windows 11 shows USB Device Not Recognized error.
I tried with different...
Hi, I'm running the sample "peripheral_uart" on an nRF52dk. It has a config called CONFIG_BT_NUS_UART_RX_WAIT_TIME, which is set to 50. The comment says the unit is milliseconds...
Hi,
I am trying to create a simple network using nrf5340 boards using BLE and Visual Studio Code as follows:
1. Scenario 1 - Very simple network: one nrf5340 communicates...
