Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
Hello all, I tried installing Segger mebedded studio on a new PC and followed the install steps from the getting started guide. Everything seems to be installed correctly...
Hi there,
we are a student project and are using the nRF51822 Chip with the MDBT40 module. We designed our own custom PCB and followed the instructions for the circuit as...
I have a subroutine that exercises the SPI interface and only at certain points in the code it won't execute the SPI subroutine and goes into the disassembly when single stepping...
SES IDE, nor nrfConnect programmer tool sees the JLink programmer attached to my PC. No "idcode" in SES. No devices appear in Programmer.
Windows10.
JLink_Windows_V764e_x86_64...
Hello,
I am beginner to work with Nordic, I am trying to setup the development environment for nRF5340 Chipset.
For that install nRF Connect Desktop v3.11.0 version. ...
Hi Team
My SES crashed suddenly. When I tick file->nRF Connect SDK Project, It show below error information. I have try to re-install the NCS from toolchain manager. It...
Hi Team,
I have nRF52 DK PCA 10040.
PC: Windows 10 pro
IDE: Keil uVision 5
Working with nRF5 SDK 17.1.0 with S132 soft device .
To execute the code , first i flashed...
Hi,
Zephyr 3.0 , nrf5340 ncs 1.9.1
i can successfully sent data with
this function ;
So it sends 2 transactions without changing cs state.
1byte tx+rx , and...
Hi,Master:
In BT core_v5.0 2.3.5.6.3 Authentication Stage 1 – Passkey Entry, as shown in the figure below
Question: Why does the process loop 20 times, verifying one bit...
Hi,
I have used the nRF Connect Mobile app to connect a BLE device to my Android device. Once bonded, I can receive temperature signals as expected without issue. I can...
Hi,
I am testing MCUboot in nrf52840 DK
I know that MCUboot can image update using slot 0, slot 1, and scratch area
If so, is it possible to update the softdevice(BLE...
Hello,
We are working on NRF52832 + nRF Connect SDK 1.8.0 for our upcoming product. We need to do OTA of our Firmware.
Could you please help with pointing to the right...
Hi Nordic,
We are using NRF52840 and the NCS sdk to design a new product which may have multiple threads designed. And each thread may need to do some BLE operation at the...
Hi,
I'm developing a peripheral driver which involves UART. I encounter an issue I'm not sure how to proceed.
In my design, I have
main.c
device_drv.c
device_drv...
