Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi,
I have power consumption issue about nRF52832 BLE application.
I found "Current consumption:Ultra-low power" informations in "nRF52832 Product Specification" as below...
Hello,
I am in a process of integrating a DFU over BLE feature into my application, my SDK5 is 17.0.2, the test board is nRF52832_XXAA.
Application size is 69404 bytes...
There is a demo zephyr/samples/subsys/fa/fat_fs. This purports to mount an SD card. Is this for the unpopulated SD socket on the nRF9160 board? The ticket https://devzone...
Hello Team,
First of all thanks a lot.
I learned so many things from your Nordic devzone:)
My problem: I have uploaded the blinky code using pca10040_s132_ble [ secure_bootloader...
Hi a bit a noobie here, but I can't connect to my nRF52840 on my custom board that I made. I have tried both an ST-link V2 with openocd, flashing it into a black magic probe...
This board is no longer recognized by SES to program code.
9:09:21.82 d:\> nrfjprog --recover ERROR: JLinkARM DLL reported an error. Try again. If error condition ERROR...
Hello, all.
I would like to connect one board that transmits data using the ble_nus , such as in the ble_app_uart example, to another that receives the data and sends...
I have been using nrf52833 Devkit with softdevice nRF5_SDK_17.0.2_d674dde have nrfconnect v3.6.1 when i merge hex file of softdevice 140 + ble_app_template then the following...
Greetings,
I've seen multiple references on how to change to the 2Mbps PHY after a connection is made, and I have that working.
Now, I'm trying to advertise at 2Mbps and...
Hi support team,
I am a beginner with Nordic nrf5 sdk for mesh. I begin with the sample light_switch. Currently I want to toggle the status (on/off) of the unprovisioned...
Hi
We need clarification about Nordic Advertiser Extensions (Instaburst) .
1. The document ( Nordic Advertiser Extensions (Instaburst) ) says that the maximum theoretical...
Sir,
How are you ?
I developted an BLE application (Segger Nordic SDK) to a chinese module and worked very very nice! I installed in 40 modules. All working
No i ordered...
Hi there,
I've just installed the "thingy91_at_client_2021-03-04_8e8c6089.hex" AT command client app on my Thingy:91 and I've connected to it via the nRF Connect LTE Link...
Is nRF5340 RF port S-parameter available?
I am looking for the S-parameter of the RF port so I can figure out the best matching circuit for my layout. The only S-parameter...
Hi ,
I want to build .. \mesh\bootloader, I know must use CMAKE, but I do not know how to use CMAKE?
Could you tell me or show me the step,please?
Thanks!
