I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
hi, nordic support
SDK version is 15.3.0
the example is ble_app_uart_c
I have modified the project based on this address： https://infocenter.nordicsemi.com/index.jsp...
Using nRF Connect SDK v2.1.0 and the nRF5340 PDK, are any of the ble mesh samples in the fw-nrfconnect-nrf repo working yet? I've tried both the mesh light and light_switch...
Hi community !
I wanted to know if it's possible to program a board as a client and as a server at the same time ?
Cause i want this card to send data into the network...
Using EmbeddedStudio_ARM_Nordic_v452_macos_x64
I am trying to build a sample for 9160-DK
In nRF Connect Options I entered:
Board directory ~/src/ncs/zephyr/boards/arm...
I am attempting to build the latest (4.1.1) pc-ble-driver with 115k2 baudrate. I have a hardware platform which supports 115k2 as maximum baud rate. It seems only the 1m version...
Hi,
I am using the NRF52840 with the usbd_ble_uart example using the latest SDK.nRF5SDK160098a08e2.
My computer (windows 7) recognize the NRF52840 as a nRF52 USB CDC...
Hi. twi_sensor As an example source, I have 2 pressure sensors. I use sdp800 and icp10101 separately and use it as twi_interface to read the sensor value well. However, we...
If I write the data from NrfConnect App and if I again go to the scanner tab without clicking on disconnect or killing the app and then if I click scan or refresh option,...
I want to transfer files to uart using ymodem protcol.
For example, when nRF52840 receives a file through BLE,
it tries to send the file back to the device connected to...
Is there a sure fire way to know for sure that my PSM configuration is correct on the nrf9160DK? I'm trying to get LTE-M + GPS working and I'm still not sure if I'm in PSM...
Hello,
We used the Nrf52810 in our project.
Currently, we found a issue: The ble is disconnected when we press the chip. Because our buttons are on top of the chip. We...
When I use circuit configuration no.5, VDD connected to VDDH and have 5V going into VBUS, I see a 1.6V output from the VDD_nRF (VDD/VDDH).
Normally when I connect a battery...
This question is a follow on to https://devzone.nordicsemi.com/f/nordic-q-a/38085/how-to-create-a-copy-of-examples-project---segger-embedded-studio .
It's clear that making...
Hi,
Can i use nRF52840 Pre Development kit as a sniffer.
Also can i use it to program my customized PCB
Note: I need to do both of above urgently so i cannot wait to...
nrf connect sdk version :1.2.0
application:nrf_: desktop
I use command " west build -b nrf52840_pca20041 -d build_pca20041" , but it report error at last.
I don't know...
