Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hello, I'm not very famililar with Airfuel, but I want to add in my device wireless charging function. I start searching solutions for this challange and I found Airfuel and...
Hi
I am facing problem with segger. Project get compiled and able to program hardware but hardware is not working until debug process is start. After put hardware in debug...
Hi,
I am trying to establish UART communication between two nRF52 Dev boards. I flashed both of them with UART peripheral example from 15.2.0 SDK and connected TX,RX and...
Hello,
Recently I'm working on the project that utilizes the nRF chip and the external memory MX25R3235F. The SDK is 14.2.
I'm trying to configure the peripheral and the...
Hi I am using nrf52832dk as master and slave for spi communication. I want to send below data over spi. 0x8000000008 0xEC000100C5 I am get confused in transfer function of...
Hey,
referring to my previous thread in https://devzone.nordicsemi.com/f/nordic-q-a/44298/running-usbd_hid_generic-in-nrf52832-using-a-custom-usb-module-mcp2200 . so am...
We are using the Development boards nRF52-DK from Nordic and trying to utilize the mergehex.exe downloaded from Nordic website.
using Segger Embedded Studio (non commercial...
Sir,
I have one nRF52840 DK and ADXL335 accelerometer. I need to get the 3-axis values, Xout, Yout & Zout, from the accelerometer and send through BLE to my nRF mobile app...
Hi,
I was going through generic_level_messages.h and generic_level_common.h files looking for the parameters for generic level status message.
I noticed that generic_level_messages...
I am using nRF51822 with SDK 10.0. I want to configure a GPIO pin which can wake up the MCU from SYSTEM OFF Mode and call its IRQ handler. Please find below configurations...
Hello,
I am using an nRF52dk with no additional hardware, in conjunction with SEGGER Embedded Studio V4.12. I started with an example from nRF5_SDK_15.3.0_59ac345 called...
Hi, I have modified the twi_scanner example of the 52840 DK to be compatible with nRFDongle.
I fully erased the dongle with Segger and passed the new hex file with SWD cable...
I used NRF connect to connect to a slave。
I want to use the central to connect to the device。
this is my code.
but the service is not found。
static void...
