When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
I'm struggling with SDKConnect and the device tree stuff... and finding it hard to get good examples or docs TBH
So, I have the sample dts files for the nRF5340DK, which...
Hello, I have a problem with the bluetooth connection to a Samsung s21. It connects for like two seconds and then disconnects immediately. Then tries to establish a new connection...
In build configuration i need to select nordic board . i have been using fanstel bt840 use nRF52840 QIAA, ARM Cortex M4F, 64 MHz . what board i have to select in this ? or...
Hi, we're having some problems and need help. We have a usage scenario: in HOST mode, the switching rate is 250k/2M every 10ms, the time slots of the two rates are different...
Hi I am trying to interface QSPI with NRF5340 dk board. I am getting build errors. I have used SPI-FLASH sample and it was working fine and I am trying to change the SPI-FLASH...
Hi,
in the new version of nrfx there is a function (nrfx _uarte _rx _new _data _check ( &uarte _instance ) , and how to get a similar result for the older version of nrfx...
Hi,
I have been testing the CAF click detector module and I find that any event callback after the click event takes almost 1000ms. That is the time between the actual click...
We are working on a project, with a working secure buttonless bootloader that works flawlessly. However I recently made it with bonds, and it works with all of the devices...
I'm experimenting with the Bluetooth Throughput sample in NCS v2.6.1. As I increase the distances between devices, I see strange gaps in the transmission from the Central...
Hello, when testing the BLE sniffer with an nRF52840 dongle (utilizing the most recent official sniffer firmware), I configured Wireshark to capture the coded PHY. After initiating...
Hi,
We are working on integrating nRF-Mesh-Library (iOS and Android) sdk into our app for mesh networking, it should support identifynode, provision, add app key and add...
I found a similar thread, but it did not solve the problem. When CDC-ACM is enabled in Device Tree, the dfu-util application cannot find the USB port. The Bootloader started...
Hi everyone
I am using nrf52840 costume board. and using NUS ( Nordic Uart Service ) as the basic start sample.
My desire:
1. UART0 and UART1 work in async mode with...
If I enter the prj.conf settings according to the lesson text then the firmware crashes with different provisioning functions from the smartphone app such as forgetting a...
It's looking more and more like a lot of my problems relate to a weak cell signal. Is the RF front end on the devkit known to be inferior to a normal cellphone? My personal...