Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
Hi,
Edited, should have pointed out that I'm using the nrf52.
I'm using a simple setup with a MEMS-microphone, and tries to read data from it.
I have setup the DMA...
Hi, I'm working with nRF52832 DK, SDK 15 on Windows with Keil5. I create Multiperiherial Nus with peer manager and fstorage and it works, but after some connetions I get an...
<error> app: ERROR 8 [NRF_ERROR_INVALID_STATE] at the same line as
ret_code = ble_advertising_advdata_update(&m_advertising, &new_data, true); APP_ERROR_CHECK(ret_code);...
Hi, maybe it's time for my dream project to come true. I have one NRF52840 DK on the table, one desktop PC, one laptop (BT 5), one iPhone X (not mine, just for a case) and...
Hey,
I am new to this , i am using nrf51822 for development , as the documentation says i downloaded the sdk and i got the nrf5 dk and i am using the Segger embedded studio...
Having problems with nrfjprog and a custom board. I connected my custom board to the NDK via P20 and flashed a program to it. The program was a variant of the pwm_library...
dear
i am using this project as slave
\nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_uart\
this project as central
\nRF5_SDK_14.2.0_17b948a\examples\ble_central...
Hello all,
Almost giving up, I'm struggling to make my nRF9160 working. I can't use the LTE Monitor at all!
Tried everything, I think, and run out of ideas. All AT commands...
I have a custom board with nrf52840 with cr2477 battery (1Ah capacity). I was download firmware to board and after a week the battery voltage dropped to critical. In the firmware...
Hello everyone.
There have a scenario, nrf52832 starts a direct advertising , but the dest ble device is not bonded(it could be any other central device), when the dest...
Hi. I am developing the nRF52832 using the NRFX module of the SDK version 15.2.0. We convert the UART signal to RS485 and communicate with RS485 to the outside. RS485 communication...
Hi,
I'm using nRF52832 on a custom board and I have tried to run sdk example nfc_url_record, but it doesn't work.
I have tried to find solution among existing answers...
Hi All,
For my project I'm using NRF52832 IC and NRFsdk. I need 2 GPIO external interrupt to get notified. I'm able to configure both pins and able to see the trigger when...
Hello Dev-Community, I have modified the Thingy Firmware for a custom made board which has also the MPU9250 with TWI connected. Everything works fine, if i use RTT Viewer...
Hi,
Referring to this thread -
If the saadc sampling is trigger by a timer (through ppi), what is the correct way to saadc_uninit() without using the global m_sampling...
