hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hi,
I need to fully take over the function HardFault_Handler
1. I overwrote the function: HardFault_Handler debug but did not stop in the function HardFault_Handler while...
the on-board J-Link is not showing up on USB anymore besides the FTDI chip still being detected.
So it's not detected anymore by neither JLinkConfig nrfprog or any other...
I'm considering various protocols for mobile robotics applications using Nordic nRF52-based transceivers. The Gazell protocol looks to have a number of appealing features...
What is the exact LFCLK control behavior with regards to control from both the APPCORE and NETCORE? The clock control figure at https://docs.nordicsemi.com/bundle/ps_nrf5340...
We have a custom board in production, which is nRF52832, s132, nrf5 SDK.
Below I provide you some code regarding the peer manager. We use a static key to pair and connect...
I have a program that to fail to start. I read the flash content use jflash, found that the only difference between the program that can run normally is the value on MBR_parameter_addr...
Hi,
This ticket is related to Case ID: 318953.
We have a nRF52820-QDAA-D-R7 on our 6-layer PCB with full ground layer beneath the chip. The chip has the external reset...
Hi,
I am currently developing a project using the nRF52810 as my controller and SEGGER Embedded Studio (version 5.42a) as my IDE. I have successfully integrated the Timer...
Hi
Is there any way to read the current value of the nPM1300 timer?
This would allow to keep track of time while the CPU is not running or rebooting (in the absence...
Dear community, I have a custom PCB based on nRF52811.
Earlier i worked on nRF52840-DK successfully with less head-ache.
How can we configure any basic project for this...
I am programming with the nRF52840DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I'd like to inquire about methods for...
Hello,
I need to write to the UICR flash multiple times. Typically, this involves disabling the softdevice, writing to the UICR, and then re-enabling the softdevice. However...
ncs v2.6.1 nrf5340
As mentioned in the document , Q1. Does CONFIG_BT_MESH_PROV_OOB_PUBLIC_KEY need to be set on the provisioner's side as well? The document only mentions...
