I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Dear all
I following the example here , over the air one, and get it basically working, thanks for the tutorial.
Now I have a few questions:
1. It looks like it always...
Hi
I am studying Matter, my setup is
chip-tool : chip-tool-android_armv7l.apk v2.1.0
OTBR : raspberry pi 3b + RCP( PCA10059 )
board : nRF52840-DK(PCA10056)
sample...
My pairing is working and shown as bonded on Android, but when the DK is reset, the bond is no longer valid.
In studying saving of bond information, I find references to...
Hi,
I am learning Matter. I have some questions:
Where can I get the resources, especially official resources, to study Matter?
What is the use of the Service discovery...
Hi,
We are developing our product using nrf5340. Currently, we are using NCS v1.9.1 for development. We need to give UART to test our Board for Certain conditions by using...
I have been learning to use the nrf52840DK for some time now, though I would consider myself still a beginner. Anyway, something has gone wrong with the kit and I am not sure...
HI,
I start a scanning and print advertising report when address match on nrf5 SDK v16.0.0 with S140 on nrf52840. It goes well until I enable GNU extension in Keil. I don...
Hello. I have a project that needs an update.
The project was working before July 2022. However, now it doesn't work anymore (VsCode run/debug doesnt work) anymore. The...
Greetings,
during test of a device, we have tried uploading a shell sample in a nrf52840dk board. However for some reason this caused the board, or at least the installed...
Hi - I am using nRF5 SDK v17.1.0 and Segger Embedded Studio v6.34a. I am testing the ble_app_buttonless_dfu for pca10040_s132.
I am compiling ble_app_buttonless_dfu_pca10040_s132...
Dear Nordic Engineers
I would like to use the DFU trigger library to realize the NRF CONNECT for Desktop enter bootloader.
I found a demo in devzone: https://devzone...
Using a MAC running Monterey, VS code runs from command line on a terminal window from everywhere. When clicking on the "Open VS Code" button from the toolchain manager it...
For the nRF5xxxxx series, it looks like it has a differential ADC with 8 positive and 8 negative channels. It also looks like it has a scan mode where it will sequentially...
Hi,
I have a nrf9160DK and flashed it with Serial LTE Modem sample, however all the AT commands are just timing out.
Configuration is default and UART 0 is used.
...
