I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
HI,
Following is the procedure to flash application we have tried:
Mass Erase
Write bootloader start address
Flash soft device
Flash bootloader
Flash application...
Hi,
I'm use ncs sdk what to send ADV_EXT_PDU Advertising, but this PDU every time send 8 advertising event, however, i'm notice that ncs sdk only use 8 second advertising...
I have a product under development that needs to send USB key codes to the PC that are outside the range that is supported by the USBD library and I am wondering the best...
Hi,
I´m developing a BLE-OTA driver for a BLE SoC and I try to use the nRF52840 dongle with my PC as the second device for the OTA mechanism by using Python and the pc_ble_driver...
I'm trying to create a HAL library to use it with zephyr application
From what I have read I need to create another module .
I can't figure out how to set up the module...
I am using the nRF52840-dk with the nRF Connect SDK v2.0.0 and for the development itself I use Visual Studio Code.
My Goal: Both the bootloader and the actual application...
Hi,
In my project, I have finished the application core code.Then I need to debug net core, but when I selected the "hci_rpmsg" target,and click the debug button.The debugger...
Hello my question is I am giving supply with lithium 18650 battery whic voltage is 3.7 to 4.2 volt but the battery falls very much below .
My question is when using HIGH...
Hello,
I'm working with NUS service and the nRF Toolbox app. I need to send multiple messages from mobile app to DK. How can I do that?. Is there a macro/script example...
I'm currently evaluating the nRF52840dk using the nRF Connect SDK to determine whether or not to port over our codebase to it from a Xiao nRF52 module I was using KVStore...
Hi,
I am trying to flash nrf52840 dk board with open thread binaries.
I see that, sporadically the device gets readback protection enabled.
I use the following command...
Hi
I have two PCA10121 and followed the instructions here to get the demo audio application to work.
The output of:
python3 buildprog.py -c app -b debug -d both
is...
I am writing my own code (no libraries etc.) on nRF52832.
For new i still have softdevice and bootloader in flash, and store my program using bootloader protocol, but my...
Hi There!
I'm using the dimmable light bulb example and have extended it with the color control attribute list. I'm using the zb_zcl_color_control_attrs_ext_t in combination...
Hi, I am working with custom board in that, trying to read NTC sensor value using 2 (NTC+ and NTC-) ADC pins. Applied Steinhart formula to convert temperature. In that, After...
