I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
hello ;
i am new for nRF52840 DK , i just want to learn how to use it , i need to deploy to bluetooth (ble5) on nrf52840dk to connect or send the data to esp32 , however...
Hi All,
Due to chip shortages we have to replace nRF52832 with nRF52810 in our design. Our application has to perform BLE scanning, but no other functionality of a BLE central...
My nRF is a central and the iOS device is the peripheral. the nRF connects to the iOS then checks via pm_conn_sec_status_get() if pm_conn_sec_status_t is encrypted, if not...
Hi I work with ble on nrf52833 I want to send my collected ble datas with uart1.In my code poll out working but fifo fill doesn't work. Any basic simple for fifo fifo fill...
Hallo,
Is nRF52840 good choice for the wireless protocols such as BLE, Zigbee and IEEE802.15.4? Can I develop these protocols in this SoC? If so is there any tutorial...
Hi All,
I have a question that when BLE connected it will show an error.
Accroding to the error,it show main.c : 163 have problem.
This is a characteristic in my...
Hi i am developing a project on custom board with mcu as nRF52833 module. This board needs to communicate with GPS module and Sim Module, so I need to use 2 UART ports to...
Hi, I am developing an application using Zephyr for nRF5340CPU. In the program there are the statements inserted to conditionaly display few parameters on norma 16x2 alphanueric...
I recently acquired an nRF52 DK and from what I have found on the Nordic site I inferred that I should install SES and VS Code and then later I found nRF Connect. They all...
tried to modify examples/ble_central/ble_app_hrs_c to collect blood pressure but found that there is no ble_bps_c folder in components/ble/ble_services/
Hello.
nRF52832
nRF5_SDK_17.1.0_ddde560
target ble_app_hids_keyboard
1. I made bonding between nRF52 and Android. and connected.
2. I remove bonding in nRF52....
Hello. I'm thinking about what I can do with peripheral rolls.
I have a question about GATT communication data. The following content was described in the Core Specification...
Hi,
We have an app, that everytime when it connects to our device writes a 0x01 to a CCCD value in order to get notifications. I see that everytime when the app does this...
I was developing application very similar to the basic ble_app_uart_pca10040_s132 example when I started getting random restarts and Segger Embedded Studio breaks at a strange...
Hello all,
Lost my VM that had a working installation and just setting everything back up.
After installing SDK 1.8.0 and all of the extensions for VsCode. Now both SEGGER...
