Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
I just bought a new laptop: IdeaPad 3 15IAU 7 running Windows 11 and I try to use it and the "nRF Connect for Desktop v5.1.0" and its "Quick Start" option to communicate via...
Can you please help us to convert following snippet from dts to mp_static.yml to use it for DFU applcation. We have external nand flash which used with littlefs and internal...
Hi all,
I have to measure the frequency of a PWM signal routed to one of the nRF52840 GPIO pins.
The signal frequency is ~3MHz.
The measurement is done with the help...
I am encountering the error message " <err> net_pkt: Uncontiguous data cannot be linearized " when already connected with nRF7002-DK to a Wi-Fi network using the EAP-TLS authentication...
I'm following the nordic academic courses, which are very nice by the way!
I've now followed three topics and I find three different variants which confuse me a lot: ...
Hi there,
So in my previous posts, I have been asking questions about setting i2s on two nRF devices in different modes. I have been successful in making it work.
...
Hello,
is it possible to read UICR at address FF8000 from a non secure application for nrf(160.
If yes, can you provide sample code and CONFIG to enable in prj.conf. ...
Hi,
I’m currently working with the nRF9151DK and using the nrf_modem_lib to test some AT commands. However, I’ve encountered an issue with the SIM.
When executing the...
When using the SPIM4 at 8 or 16 MHz, the clock looks nice and even. But at 32 MHz it consistently skips a half beat on the 16th clock pulse. In other words, while all the...
I am working on nRF54L15 and I want to store some user data in flash and for that I want to define the partitions.
I have selected the Target: nrf54l15dk/nrf54l15/cpuapp...
I am running smp_svr demo on my nrf54l15DK board, and use mcumgr command on my linux.
I could connect to my ble device and echo hello successfully (via peer_name='Zephyr...
Body:
Hello Nordic Team and Community,
I am working on a project using an nRF52840 chip on a custom breakout board . I am not using any pre-made development boards or...
During the testing phase of my device I use the Zephyr (uart) logging module and the Zephyr shell module(CONFIG_SHELL_LOG_BACKEND=y). Shell is mostly disabled, and is enabled...
I followed the migration guide for NCS 2.8.0 here for a custom board with engineering rev B silicon. After doing so I can't flash the board anymore and it gives me this error...
