I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hello Nordic!
I want to control the battery level, and set alarms... I know that there is a cluster callled PowerConfig cluster and I have been reading it, but I acan't...
Hello,
Sorry in advance if it sounds simple, i'm a beginner but I read AT command interface — nRF Connect SDK 1.5.99 documentation (nordicsemi.com) except that I can't retrieve...
Hi!
I'm currently working on a project thats based off of the nrf desktop keyboard. I'm using the Taiyo Yuden eysgcnzxx.
I just wanted to inquire the functionality of...
We have a Zigbee device that doesn't seem to use ZCL to transfer data and I have been trying to see if there is a way to get it working with an nrf52840 acting as a coordinator...
Hi, can we connect and enable the BME680 in the asset tracker code for the nRF9160DK?
It is already on the Thingy and I notice there is a switch CONFIG_BME680 in the code...
Tried to connect and Flash the hex file to enable BLE sniffing on the DK. However, the Connect desktop app was not able to detect the Development Kit.
All Steps mentioned...
Hello,
I am working on the Nordic nRF52840 development board to create a thread network and I want to use Raspberry Pi4 as thread board border router. The nordic SDK provide...
Following the insn here: https://devzone.nordicsemi.com/f/nordic-q-a/54591/nrf_serial_event_drv_err-what-is-the-cause
I found that under certain conditions, I get ERRORSRC...
Hi Nordic Community,
I have been experimenting with samples in NCS and making modifications.
Sometimes adding some code causes a hardfault during runtime. I can often...
Hello.
My application is an I2S Master that transmits audio data to an audio codec. I need to setup a transmit buffer using EasyDMA. Is EasyDMA used by default when using...
Hello,
we developed an application with a nRF52840DK as central and a custom board with a nRF52832 chip as peripheral. The peripheral sends data via NUS with a data rate...
Hi,
I'm working on the secure_bootloader example. I am having problems with micro ecc. When I compile the project, it gives an error like this.
I'm trying to follow...
The nRF5340 net-core examples (e.g., radio_test, hci_rpmsg) work fine with the 'west' build system. However, with SES, download fails with the error similar to below although...
I'm trying to narrow down the cause of a Softdevice assertion happening in S132 7.2.0 at PC=0x15810.
We set up a proprietary RF project which utilises parts of the SDK for...
Hi all,
I have a nRF52DK as peripheral and a nRF52840DK as central. I want to send data from the peripheral to the central with a data rate of 50 kBit/s.
I added a continuous...
