I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
The specifications for Flash programming in section 4.3.7.1 page 21 is blank in the nRF52810 Product specification 1.0. Can you please provide the values for this table?
Hi all,
I am not able to update the modem firmware over usb/mcboot with the programmer on my Thingy91. I have tried both on linux and win 10, the problem is the same. The...
Hi,
I have been using the NUS on nRF52832 DVK with no issues, however, when I migrated to the nRF52840 DVK and a custom board based on the 52840, the NUS characteristics...
Hello Nordic Community,
I am currently following the SMP guide provided here: https://docs.zephyrproject.org/latest/samples/subsys/mgmt/mcumgr/smp_svr/README.html
The...
Hey,
I am wondering if it is possible to run MTD and SED on the CoAP server on nRF Connect SDK v1.4.0.
I have looked at the question " How do I set up CoAP Server whit...
Hello,
We are going to design our new product using NRF52832. Please suggest if there is any other better IC which has higher transmission range, higher RAM and with less...
there is a module in the skylab project on the nRF52832 chip and it does not agree with the tablet, which is old BT. Is it possible, through the firmware or SDK, to downgrade...
Hi
After nRF Connect for desktop was upgraded to v3.6.1, programmer application cannot recognize all DK boards, including PCA10040/PCA10056/PCA10090.
It showed the error...
Can I use nRF21 in GPIO mode (not SPI) using the PA/LNA assist feature of the S112 soft device?
Per section 5.3 of the datasheet, it seems I could wire the PDN pin to be...
Hi,
I am learning how to write and read from flash memory on nRF52833 dev board for a BLE application.
I followed the heart rate example as shown in https://devzone.nordicsemi...
I am writing an application for the nRF52DK which uses two additional push buttons besides the 4 already present on the board.
Using GPIOTE the detection of the button press...
I have a working project that uses the NRF_LOG module to send debug outputs over the UART backend. When just using the logging module everything works correctly.
I added...
Hi,
Is it possible to set multiple APNs in nrf9160 and with fallbacks to next APN if one not working?
Suppose if we set 2 APNs at CID=0 and CID =1 positions using AT+CGDCONT...
