I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
Are there examples of HW and SW to allow Power Amp, LNA, and TX/RX switch to be connected to the nRF52840_DK?
Or can you tell me what PIN on the chip or connector and pin...
Hello -
We are developing some low power code on the nRF52840-DK, using SDK 15.3.0 on FreeRTOS. I noticed that in the port_cmsys_systick.c file, in the vPortSuppressTicksAndSleep...
I am building a prototype that will use the nrf52840, with limited space. Would making a small pcb antenna or using a chip antenna be better and what is the setup needed for...
Hi,
I would like to measure the voltage generated by a Thermoelectric generator. The voltage vary between -250mV and 250mV depending on the temperature gradient.
If...
I'm looking for alternative xtal's (mhz + rtc) for use on boards where space is very limited.
Silego's GreenCLK3 looks like a great option, though that one is right now...
hi,
I want to use the Bluetooth Low Energy in nRF Connect for desktop. But I have no DK or dongle.
When I use my own development board and the MCU is nRF 52832, it can...
Hi
I am wondering how to choose among different logger mechanisms available in nRF SDK v16.0.
I noticed that some examples doesn't use any logger at all (e.g. blinky...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
I have cleared the WDT with "nrf_drv_wdt_channel_feed". I want to make sure it is cleared. Which register can be used to confirm...
Hi I am using Keil ARM with JLINK to debug the NRF52832. I can download the flash on the PCBA but when I try to debug step-by step, it only runs on the assembly window but...
Hello ...
Implementing an app for both nRF51822 and nRF52810 and need a long-term clock with 100 Hz counter frequency to timestamp sensor events. By long-term, I mean at...
HI,
I've been looking at the nRF52811 registers for AoA/AoD, and decided to try and at least get CTE enabled on the basic Nordic uart app. I found this post:
https://devzone...
Hello. In acrording to:
How the bridge exchange information between mesh network and mobile device
The bridge using Nordic UART Service to conduct the command/response...
Struggling with a similar problem that has been popping up for many users. I am already stuck on setting up ncs where installation of pygit2 is failing. I managed to alleviate...
There is an SPIM unexpected interrupt issue which I have replicated in a totally bare-bones piece of code using no Nordic library drivers. In my bare-bones SPI code I get...
hi
im trying to program my nrf9160 using nRF connect 3.3.0 (with latest programming tool).I have jlink 6.56a installed
ive been occasionally able to wipe the nrf9160...
