After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
Hi,
I am trying to run the NRFX_SPIM example project code on my DK. But my DK is 10040/nrf52382 and the example project given in SDK15.2 only has a folder for 10056. Should...
Good morning
I'm new to these SoC systems, but I've developed a custom board with the nRF52810QCAA chip and I'm using the example (ble_app_eddystone) of the SDK15.2. softdevice...
Hello
I am now using nrf52832 and BLE communication with an Android terminal.
BLE communication is a beginner.
I am using nRF_SDK_15.0.0_a53641.
Since I programmed...
It seems possible, but I can't quite figure out how to use nrf_ble_scan_filter_set to use more than one device name. Any assistance? Alternatively, is it possible to use wildcards...
Hi,
In GATT level, on the receiving side - Is it possible to receive a corrupted packet or does the LL identify and discards such packets?
Specifically
- Will host...
Hi
I segger project get compiled and download successfully but it didn't start work. After put it in debug mode, it start working even after removed it from debug mode working...
I am working on a custom board with two MCUs, one nRF52840 and one older MCU.
In the previous iteration of this PCB the old MCU was connected to USB through an FTDI FT232...
Hi,
I've developed a relay application based off of the ble_app_hrs_rscs_relay_pca10040_s132 example in SES using a Laird BL652 module (nRF52832 underlying device). Presently...
Hi
My application with SDK11 S132 softdevice is having some unknown issues that will make wdt or hard fault handler happen. And I am trying to use the following code to...
Hello I am using eddystone-beacon example from sdk 12.3 but i am unable to get notification on android phone,nearby setting is also enabled ,please help??
Hello,
I’m looking for an example using the Segger IDE that would read the SAADC and transmit via BLE.
The following example seemed like a good starting place:
...
I am currently working with an nRF51822, SDK 10 (can't be changed), s110. I have a nRf51822-DK (aka pca10028) and wanted to try the d fu_dual_bank_ble_s110_pca10028 example...
I use the nrf_drv_pwm to generate a pwm sequence,
The sequence works fine, but between sequences and at the end I am unable to control the pin.
It is always high unless...
Hi guys
I am looking for export control related information on NRF52832-QFAA-R7, in particular: 1) Is the product a controlled dual use item under EU Regulation 428/2009...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
