Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
I am trying to get the S132 Central Multilink example to run with 20 peripherals instead of 8. So far, I have made the following modifications:
In sdk_config:
Increased...
I wonder about the accuracy specifications in chapter 9 of the ppk user guide. It says +-20% of readout on average value. Is this only the calculated average of the python...
Using S130 to request notifications of radio activity as:
fails with NRF_ERROR_INVALID_PARAM.
Is there a reason this combination is disallowed? The use case for it is...
I would like to add the UART part to my application. But I will get these errors:
..........\components\libraries\uart\app_uart_fifo.c(109): error: #20: identifier "UART0_CONFIG_PSEL_TXD...
I am working on an automation project wherein I have to integrate ESP8266 with nRF51SDK. So, I want to serially send and receive strings over a physical UART connection, not...
Hello All
For our project we are using teensy3.6 as our main micro controller unit and NRF24L01 as RF transmission device.
Our project include mainly 2 parts
1) Data...
Hi. I've encountered a problem with some of my nrf24le1 chip (near every 5th piece) - current in deep sleep mode is very high (30-80 uA), if i change it to another chip, then...
Does the ui depend on the app design(nrf connect app) or on writing data in the characteristics. For the predifined i am getting a switch but for the one i added i have to...
Dear sir,
Sir I am trying to send an array of 40 values via nrf51422 to your andriod app "BLE SCANNER" by using the function "ble_nus_string_send ". But it is sending only...
I've tried ble_app_uart, nrf_serial.c etc. and none seems satisfactory.
I can write to the logger logger/uart during DEBUG, but it doesn't seem to succeed in RUN.
Question...
Hello,
I'm using :
- SDK 11 s132
- nRF52832
I want to protect my flash against dumping from swd but I'm working also with DFU from our custom app.
Is it possible...
Randomly on my nrf52832, sd_power_system_off() is returning NRF_ERROR_NOT_SUPPORTED and I'm looking for tips on how to figure out why. I'm using a Bluetooth soft device and...
Hello,
May I please check if the following is correct? On the nRF52840-PDK board (v0.9.3, 2017.47), the "VTref" pin of the "Debug In" header is connected to VDD. Should...
I need to upgrade and existing nrf51 S110 system based on SDK 8.x to something that supports the same functionality and also supports both a nrf51 (during the transition)...
