Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I just want to learn if we can use high-freq clock to measure time in nanosecs precision.
SoC: nRF52840
SDK: nRF Connect SDK (v1.9)
I know that it was not possible...
Hi guys,
I am experimenting with OTA buttonless DFU.
I included the Buttonless Secure DFU Service to my application and I managed to flash the new image over the air through...
Hi there,
As the title says, I only get an all white window whenever I open an app in nRF Connect for Desktop (this happens for all apps).
If I try to reload the window...
I try to get the Direct Test Mode App to work on a Windows 10 Notebook. (for System Details see attached system report and verbose logfile).
Software versions:
nRF Connect...
Hello,
I'm using the PCA100095 NRF5340 development board and developing with the NRF Connect extension for VSCode v2022.3.104 .
When attempting to use the CMSIS intrinsics...
Hello,
In my project i am using nrf52840 with custom board, here i am using BLE UART to send the data from the mobile to device and sending data from another sensor board...
I would like to add Just Works security to our battery service (BAS). However, I could not find such a setting anywhere, so I looked into it and found that in bas.c BT_GATT_SERVICE_DEFINE...
I am troubleshooting a board with no working RF. On looking deeper it appears that the HFCLK is not starting (NRF_CLOCK->EVENTS_HFCLKSTARTED is never set).
This is on a...
Hello,
I am currently working on the NRFX QDEC library with a decoder to be used with a servo motor.
We manage to initialize and enable the QDEC and IRQ and we get...
Hi,
I am facing a problem in adding a power down feature in my application, the details of the application are as follows,
I am using the sensor server example given...
Hey guys,
I have a small concern and decided to ask here, as i was not able to found answer neither in zephyr or nrf sdk docs (not even sure which one apply to my question...
I use the DF example.In Rx.i use both nrf52833 boards as test.i use NCS 1.9.1.
In rx,i use the silab's 16 antenna array for receving antenna array.
because it has 16 antennas...
Topology:
Raspberry Pi A Raspberry Pi B
|(USB connect) |(USB connect)
nRF52840 dongle A )))) Thread (((( nRF52840 dongle B
Software:
nrf52840-dongle: ot-rcp.hex...
In the online power profiler for nRF52832, when I look at the advertising (Tx/Rx) power consumption I see that if I set the Tx payload to 0 bytes the Tx time modeled is 128us...
