I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
Hello, I experience some issues with NRF9160 and eSIM card. SIM_1V8 always output 0v and "AT%XSIM?" return "%XSIM: 0". I want to know if there is prior software configuration...
hello all,
I am trying to find the best power efficiency to transferring a pack of data(30 byte each time) from one nrf52 to another nrf52. I have a 80 uA in average power...
Hi all
So i had a working running example on SDK Thread and Zigbee V3.0.0. This flavor used the softdevice s140_nrf52_6.1.1_softdevice.hex I've migrated to the new SDK...
Hey All
I've found thread, dealing with this problem here: https://devzone.nordicsemi.com/f/nordic-q-a/77775/nrf_ble_lesc-nrf_crypto_ecc_key_pair_generate-returned-error...
I try to connect my nrf5340 CoAP server via my border router with CoAP Messages (with the IP address) from a computer. Is that possible? And if so, How?
I made a border...
I want to read peripheral's characteristics value in a fixed time interval or an event-based in the central.
I am using the nRF52840 Evalution board and SDK_17.0.2.
Here...
hi Support team,
Customer tested mesh SDK4.2, and now had one question:
their product is end node, and once button pressed, MCU is waked up and send the message to server...
in the gps example, there is a struct
nrf_modem_gnss_pvt_data_frame
in which contains the accuracy in meters, by documentation definition, it's /** Accuracy (2D 1...
Hi,
Facing some issue in creating sample application in vscode
nCS sdk V1.7.0, created sample hello world project and added build configuration for bl653_dvk
getting...
Hello all. Now I am making a BLE network with multiple peripherals and central based on NUS. How could I make data transfer between the central and specific peripherals? I...
Hello,
I would like to develop OpenThread applications that run under ZephyrRTOS for the nRF52840 processor. It appears that there are 3 possible development approaches...
Hello I'm trying to implement the DFU Trigger library into my project. to get following function:
" When the trigger library is added to an application, it allows a connected...
Greetings,
I am trying to get the nRF5340 DK to run on the coin cell battery attached to it. I removed the plastic and the USB cable then I put the "nRF power source" switch...
Hi team,
When we set fast advertisement timeout (uint32_t ble_adv_fast_timeout; /**< Time-out (in units of 10ms) for fast advertising. */) to a value greater than 0xFFFF...
i am using Laird smartBASIC for my programming of the BL653. I cloned the firmware of the evaluation board using the supplied Laird batch files and the J-LinkARM interface...
