Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
SDK: NCS 3.0.2
Part: NRF52840
I am running the NRF52840 as an HCI controller over SPI. I can advertise and connect. However, I need to advertise while connected and support...
Hi,
I wanted the zigbee firmware to support BLE OTA. so I downloaded the latest zigbee SDK from the following link " ">github.com/.../pulls".But the compilation encountered...
Background
I'm working on a BLE application for the nRF52811 and facing significant flash memory constraints when trying to implement OTA/DFU functionality.
From my understanding...
Hi all,
I'm working on optimizing the power consumption on my nRF52840 DK and need some guidance. Currently measuring ~5µA average idle current via PPK2, but I need to reduce...
Hello
I am trying to perform a firmware update over Bluetooth but without using the external flash on the nRF52840-dk.
At this point I can successfully build the smp_svr...
Hi,
I have custom hardware using the NRF52810. Due to its very small RAM size, I developed the code on the NRF52DK_NRF52832 and then removed functionalities to make it fit...
Hi The Nordic team,
After my device reconnects to the gateway from offline again, I don't know what I am doing with this timing every 1s. This situation will not happen...
Hi，
I developed a gateway for converting an MCU to ble Bluetooth. The MCU connects to 8 BLE hosts via UART, and each Bluetooth host can connect to one Bluetooth slave. All...
Hello,
I am trying to configure COMP peripheral on my NRF54L15 DK. I am using P1.11 pin (AIN4) as single ended input for this purpose. For now I am trying only to evaluate...
Hello,
I’m working on a project where I intend to integrate the nRF9151 as a standalone modem , communicating with my external MCU via UART using AT commands .
My goals...
Hi,
Currently I am using nRF52840 as nodes for mesh network. However, by reading the sdk5 documents and example, I did not see any clues to update the firmware with DFU...
After the update to extension version 2025.8.654, the extension can no longer find the nRF SDK in my west workspace in the build configuration. If I revert to extension v2025...
I made a PCB board, but I couldn't connect to the chip with JLink. I used a lithium battery to power VDDH. I want to test if there is any problem with the hardware. I tried...
I am using NRF5340 with NRF connect (Zephyr) and logging out to RTT (printk or printf, etc) , which works but sometimes I get buffered fragments and dont see the rest of the...
