Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Question 1:
The nRF9160 datasheet V2.0 claims the sensitivity is: CATM=-108dBm (mid band); NBIOT=-114dBm (mid band).
However when the unit connects, we get a printout...
So in the MQTT example the following function is used to write the CA certificate to the modem so a TLS connection can be setup.
In our code/TLS setup we want to use Client...
Sorry this is an urgent request and we could not find much information on the internet about this module. We have a tight schedule so it might be a good idea to post here...
Hi, Hope your are well, i am currently in the final part of my project where i am SPI Gyroscope float data from one nordic nrf52dk (S132) to another such that i can analyize...
I am running read str 0x3e000 12 via UART line but there is nothing which gets printed on the terminal.
Even if i write some hex value to a particular flash memory location...
Hi there,
I have set up the nRF2427 with the nRFgo Starter Kit motherboard (nRF6700). The motherboard is recognized and I have all of the 2.4GHz options available. I would...
Hello,
I am working on the nrf52832 board with SDK16.
I am using a custom BLE example.
My TWI and BLE code work ok individually but when I integrate them it does not...
Using S132 v7.2, I'm getting a hard fault at PC 0x00015810 (I see the flag set in SEGGER, and the console outputs a SOFTDEVICE ASSERT FAILED error) that I'm working on manually...
Hi,
The 'nRF Connect' SDK (v1.4.99-dev1) sample OpenThread CLI is programmed to receive 'ot' commands from UART console. When configured with multi-protocol support, the...
Hello,
I have a problem that sometimes the supl_client_session() function halts the system by not finishing and ending the session while getting the timeout expired SUPL...
Hi
I can't find fwid for sd132 7.2
|s132_nrf52_5.0.0|0x9D| |s132_nrf52_5.1.0|0xA5| |s132_nrf52_6.0.0|0xA8| |s132_nrf52_6.1.0|0xAF| |s132_nrf52_6.1.1|0xB7| |s132_nrf52_7...
Hi there,
Our team is developing an application based on the nRF5340-DK - we are developing on the DK while our hardware is in transit. Our schematic largely follows the...
Hello, I use the internal crystal, the application in my board runs normally and it shows the board is in fast advertising state. However, I can't find bluetooth signal through...
I'm running the Zephyr hci_usb sample on a nRF52833DK to see if I can use it as a Bluetooth dongle on my Ubuntu dev machine. It appears as /dev/ttyACM0, so:
sudo btmon ...
Dear Nordic,
I have a BLE mesh product that is in pre-production. The mesh gateway is composed of an nRF9160 and nRF52840 with a UART link connecting them. The nRF52840...
